Omron, ZS Series

ZS-HL Series

Very High-performance Sensors that Support Core Quality from Very Long-range to Extremely Precise Measurements

Range of models with measuring center distance of 20 to 1,500 mm.
Achieves maximum resolution of 0.25 μm.
Maximum response speed of 110 μs.
Parallel output supported.

All Models Are Class 2 Lasers.

Extreme Stability

Ideal Size and Stability
Head Size

Complete sensing stability with optimum Sensor Head size for best performance and holding mechanism secured at 3 points. (See note.)
Note: ZS-HLDS2T not applicable.

Superior Moving Resolution
Increased Lens Resolution

Moving resolution (error based on workpiece surface position) has been reduced dramatically by optimizing the optical system with increased sensitivity and resolution of the light receiving lenses.

Reduced Error for Different Materials
2D CMOS

With a CCD, the charge overflows to the next pixel when excessive light is received. This phenomenon does not occur with CMOS, so there are no effects from light fluctuations from different materials or excessive light reception.

ZS-L Series

Standard Sensors Most Suitable for a Variety of High-precision Displacement Measurements, Including Spot Detection, Wide-range Detection, and Long-distance Detection.

Beam Shapes
Spot and line beam selection.

Wide Range of Products
Long-range, middle-range, and short-range models.

last update: June 01, 2015

ZS-HL/L-series Sensor Controllers

Model			ZS-HLDC11/LDC11	ZS-HLDC41/LDC41
No. of samples to average			1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1,024, 2,048, or 4,096
Number of mounted Sensors			1 per Sensor Controller
External interface	Connection method		Serial I/O: connector, Other: pre-wired (Standard cable length: 2 m)
	Serial I/O	USB 2.0	1 port, Full Speed (12 Mbps max.), MINI-B
	Serial I/O	RS-232C	1 port, 115,200 bps max.
	Output	Judgment output	HIGH/PASS/LOW 3 outputs NPN open collector, 30 VDC, 50 mA max., residual voltage 1.2 V max.	HIGH/PASS/LOW: 3 outputs PNP open collector, 50 mA max., residual voltage 1.2 V max.
	Output	Linear output	Selectable from 2 types of output, voltage or current (selected by slide switch on bottom). • Voltage output: -10 to 10 V, output impedance: 40 Ω • Current output: 4 to 20 mA, maximum load resistance: 300 Ω
	Inputs	Laser OFF, ZERO reset timing, RESET		ON: Short-circuited to supply voltage or within 1.5 V of supply voltage. OFF: Open (leakage current: 0.1 mA max.)
Functions			Display: Measured value, threshold value, voltage/current, received light amount, and resolution/terminal block output 2 Sensing: Mode, gain, measurement object, head installation Measurement point 1: Average, peak, bottom, thickness, step, and calculations Filter: Smooth, average, and differentiation Outputs: Scaling, various hold values, and zero reset I/O settings: Linear (focus/correction), judgments (hysteresis and timer), non- measurement, and bank (switching and clear) *2 System: Save, initialization, measurement information display, communications settings, key lock, language, and data load Task: ZS-HLDC[]1: Single task or multitask (up to 4), ZS-LDC[]1: Single task
Status indicators			HIGH (orange), PASS (green), LOW (orange), LDON (green), ZERO (orange), and ENABLE (green)
Segment display		Main digital	8-segment red LED, 6 digits
Segment display		Sub-digital	8-segment green LEDs, 6 digits
LCD			16 digits x 2 rows, Color of characters: green, Resolution per character: 5 x 8 pixel matrix
Setting inputs		Setting keys	Direction keys (UP, DOWN, LEFT, and RIGHT), SET key, ESC key, MENU key, and function keys (1 to 4)
Setting inputs		Slide switch	Threshold switch (2 states: High/Low), mode switch (3 states: FUN, TEACH, and RUN)
Power supply voltage			21.6 V to 26.4 VDC (including ripple)
Current consumption			0.5 A max. (when Sensor Head is connected)
Ambient temperature			Operating: 0 to 50°C, Storage: -15 to +60°C (with no icing or condensation)
Ambient humidity			Operating and storage: 35% to 85% (with no condensation)
Degree of protection			IP20 (IEC60529)
Materials			Case: Polycarbonate (PC)
Cable length			2 m
Weight			Approx. 280 g (excluding packing materials and accessories)
Accessories			Ferrite core (1), instruction sheet

*1. Can be used with ZS-HLDC[]1 when Multitask Mode selected.
*2. Terminal block output is a function of the ZS-HLDC[]1.

ZS-HL-series Sensor Heads

Model		ZS-HLDS2T		ZS-HLDS2VT	ZS-HLDS5T
Applicable Controllers		ZS-HLDC series
Optical system		Regular reflection	Diffuse reflection	Regular reflection	Diffuse reflection	Regular reflection
Measuring center distance		20 mm	5.2 mm	25 mm	50 mm	44 mm
Measuring range		±1 mm	±1 mm	±2 mm	±5 mm	±4 mm
Light source		Visible semiconductor laser (wavelength: 650 nm, 1 mW max., JIS Class 2)
Beam shape		Line beam
*Beam diameter 1**		1.0 mm × 20 μm		2.2 mm × 45 μm	1.0 mm × 30 μm	3.5 mm × 60 μm
*Linearity 2**		±0.05%F.S.		±0.2%F.S.	±0.1%F.S.
*Resolution 3**		0.25 μm (No. of samples to average: 256)		0.6 μm (No. of samples to average: 128)	0.25 μm (No. of samples to average: 512)	1 μm (No. of samples to average: 64)
Temperature characteristic *4		0.01%F.S./°C		0.1%F.S./°C	0.01%F.S./°C
Sampling cycle		110 μs (High-speed Mode), 500 μs (Standard Mode), 2.2 μs (High-precision Mode), 4.4 μs (High-sensitivity Mode)
LED Indicators	NEAR indicator	Lights near the measuring center distance, and closer than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
LED Indicators	FAR indicator	Lights near the measuring center distance, and farther than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
Operating ambient illumination		Illumination on received light surface: 3000 lx or less (incandescent light)
Ambient temperature		Operating: 0 to 50°C, Storage: -15 to 60°C (with no icing or condensation)
Ambient humidity		Operating and storage: 35% to 85% (with no condensation)
Degree of protection *5		IP64		IP67	Cable length 0.5 m: IP66, cable length 2 m: IP67
Materials		Case: Aluminum die-cast, Front cover: Glass
Cable length		0.5 m, 2 m		2 m	0.5 m, 2 m
Weight		Approx. 350 g			Approx. 600 g
Accessories		Laser labels (1 each for JIS/EN, 3 for FDA), ferrite cores (4), insure locks (2), instruction sheet		Laser labels (1 each for JIS/EN), ferrite cores (2), insure locks (2), instruction sheet	Laser labels (1 each for JIS/EN, 3 for FDA), ferrite cores (4), insure locks (2), instruction sheet

Model		ZS-HLDS10		ZS-HLDS60	ZS-HLDS150
Applicable Controllers		ZS-HLDC series
Optical system		Diffuse reflection	Regular reflection	Diffuse reflection	Diffuse reflection
Measuring center distance		100 mm	94 mm	600 mm	1500 mm
Measuring range		±20 mm	±16 mm	±350 mm	±500 mm
Light source		Visible semiconductor laser (wavelength: 650 nm, 1 mW max., JIS Class 2)		Visible semiconductor laser (wavelength: 658 nm, 1 mW max., JIS Class 2)
Beam shape		Line beam
*Beam diameter 1**		3.5 mm × 60 μm		16 × 0.3 mm (at 500 mm)	40 × 1.5 mm (at 1,500 mm)
*Linearity 2**		±0.1%F.S.		±0.07%F.S. (250 to 750 mm), ±0.1%F.S. (750 to 950 mm)	±0.2%F.S.
*Resolution 3**		1 μm (No. of samples to average: 64)		8 μm (No. of samples to average: 64 at 250 mm), 40 μm (No. of samples to average: 64 at 600 mm)	500 μm (No. of samples to average: 64)
Temperature characteristic *4		0.01%F.S./°C
Sampling cycle		110 μs (High-speed Mode), 500 μs (Standard Mode), 2.2 μs (High-precision Mode), 4.4 μs (High-sensitivity Mode)
LED Indicators	NEAR indicator	Lights near the measuring center distance, and closer than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
LED Indicators	FAR indicator	Lights near the measuring center distance, and farther than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
Operating ambient illumination		Illumination on received light surface: 3000 lx or less (incandescent light)		Illumination on received light surface: 1000 lx or less (incandescent light)	Illumination on received light surface: 500 lx or less (incandescent light)
Ambient temperature		Operating: 0 to 50°C, Storage: -15 to 60°C (with no icing or condensation)
Ambient humidity		Operating and storage: 35% to 85% (with no condensation)
Degree of protection *5		Cable length 0.5 m: IP66, cable length 2 m: IP67		IP66 *6
Materials		Case: Aluminum die-cast, Front cover: Glass
Cable length		0.5 m, 2 m
Weight		Approx. 600 g		Approx. 800 g
Accessories		Laser labels (1 each for JIS/EN, 3 for FDA), ferrite cores (4), insure locks (2), instruction sheet

*1. Defined as 1/e² (13.5%) of the center optical intensity at the actual measuring center distance (effective value). The
beam diameter is sometimes influenced by the ambient conditions of the workpiece, such as leaked light from the
main beam.
*2. This is the error in the measured value with respect to an ideal straight line.
Linearity may change according to the workpiece.
The following options are available.

Model	Diffuse reflection	Mirror reflection
ZS-HLDS2T	SUS block	Glass
ZS-HLDS2VT	---	Glass
ZS-HLDS5T	White alumina ceramic	Glass
ZS-HLDS10	White alumina ceramic
ZS-HLDS60/HLDS150	White alumina ceramic	---

*3. This is the peak-to-peak displacement conversion value in the displacement output at the measuring center distance
in high-precision mode when the number of samples to average is set to within the graph.
The maximum resolution at 250 mm is also shown for the ZS-HLDS60. The following options are available.

Model	Diffuse reflection	Mirror reflection
ZS-HLDS2T	SUS block	Glass
ZS-HLDS2VT	---	Glass
ZS-HLDS5T	White alumina ceramic	Glass
ZS-HLDS10	White alumina ceramic
ZS-HLDS60/HLDS150	White alumina ceramic	---

*4. This is the value obtained at the measuring center distance when the Sensor and workpiece are fixed by an
aluminum jig. (typical example)
∗5. Protection structure of connector area is IP40.
∗6. Ask your OMRON representative about Sensor Heads with IP67 protection.

ZS-L-series Sensor Heads

Model		ZS-LD20T		ZS-LD20ST		ZS-LD40T		ZS- LD10GT	ZS- LD15GT
Applicable Controllers		ZS-HLDC/LDC series
Optical system		Regular reflection	Diffuse reflection	Regular reflection	Diffuse reflection	Regular reflection	Diffuse reflection	Regular reflection
Measuring center distance		20 mm	6.3 mm	20 mm	6.3 mm	40 mm	30 mm	10 mm	15 mm
Measuring range		±1 mm	±1 mm	±1 mm	±1 mm	±2.5 mm	±2 mm	±0.5 mm	±0.75 mm
Light source		Visible semiconductor laser (wavelength: 650 nm, 1 mW max., JIS Class 2)
Beam shape		Line beam		Spot beam		Line beam
*Beam diameter 1**		900 mm x 25 μm		20 μm dia.		2000 x 35 μm		Approx 25 x 900 μm
*Linearity 2**		±0.1%FS
*Resolution 3**		0.25 μm		0.25 μm		0.4 μm		0.25 μm	0.25 μm
Temperature characteristic *4		0.04%FS/°C		0.04%FS/°C		0.02%FS/°C		0.04%FS/°C
Sampling cycle		110 μs (High-speed Mode), 500 μs (Standard Mode), 2.2 μs (High-precision Mode), 4.4 μs (High-sensitivity Mode)
LED Indicators	NEAR indicator	Lights near the measuring center distance, and closer than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
LED Indicators	FAR indicator	Lights near the measuring center distance, and farther than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
Operating ambient illumination		Illumination on received light surface: 3000 lx or less (incandescent light)
Ambient temperature		Operating: 0 to 50°C, Storage: -15 to 60°C (with no icing or condensation)
Ambient humidity		Operating and storage: 35% to 85% (with no condensation)
Degree of protection *5		Cable length 0.5 m: IP66, cable length 2 m: IP67						IP40
Materials		Case: Aluminum die-cast, Front cover: Glass
Cable length		0.5 m, 2 m
Weight		Approx. 350 g						Approx. 400 g
Accessories		Laser labels (1 each for JIS/EN, 3 for FDA), ferrite cores (2), insure locks (2), instruction sheet						Laser safety labels (1 each for JIS/EN), ferrite cores (2), insure locks (2)

∗1. Defined as 1/e² (13.5%) of the center optical intensity at the actual measuring center distance (effective value).
The beam diameter is sometimes influenced by the ambient conditions of the workpiece, such as leaked light
from the main beam.
∗2. This is the error in the measured value with respect to an ideal straight line.
The standard workpiece is white aluminum ceramics and glass in the regular reflection mode.
Linearity may change according to the workpiece.
∗3. This is the peak-to-peak displacement conversion value in the displacement output at the measuring center
distance in high-precision mode when the number of samples to average is set to 128 and the measuring
mode is set to the high-resolution mode.
The standard workpiece is white aluminum ceramics and glass in the regular reflection mode.
∗4. This is the value obtained at the measuring center distance when the Sensor and workpiece are fixed by an
aluminum jig. (typical example)
∗5. Protection structure of connector area is IP40.

ZS-L-series Sensor Heads

Model		ZS-LD50		ZS-LD50S		ZS-LD80
Applicable Controllers		ZS-HLDC/LDC series
Optical system		Diffuse reflection	Regular reflection	Diffuse reflection	Regular reflection	Diffuse reflection	Regular reflection
Measuring center distance		50 mm	47 mm	50 mm	47 mm	80 mm	78 mm
Measuring range		±5 mm	±4 mm	±5 mm	±4 mm	±15 mm	±14 mm
Light source		Visible semiconductor laser (wavelength: 650 nm, 1 mW max., JIS Class 2)
Beam shape		Line beam		Spot beam		Line beam
*Beam diameter 1**		900 × 60 μm		50 μm dia.		900 × 60 μm
*Linearity 2**		±0.1% FS
*Resolution 3**		0.8 μm		0.8 μm		2 μm
Temperature characteristic *4		0.02% FS/°C		0.02% FS/°C		0.01% FS/°C
Sampling cycle		110 μs (High-speed Mode), 500 μs (Standard Mode), 2.2 ms (High-precision Mode), 4.4 ms (High-sensitivity Mode)
LED Indicators	NEAR indicator	Lights near the measuring center distance, and closer than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
LED Indicators	FAR indicator	Lights near the measuring center distance, and farther than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
Operating ambient illumination		Illumination on received light surface: 3000 lx or less (incandescent light)
Ambient temperature		Operating: 0 to 50°C, Storage: -15 to 60°C (with no icing or condensation)
Ambient humidity		Operating and storage: 35% to 85% (with no condensation)
Degree of protection *5		Cable length 0.5 m: IP66, cable length 2 m: IP67
Materials		Case: Aluminum die-cast, Front cover: Glass
Cable length		0.5 m, 2 m
Weight		Approx. 350g
Accessories		Laser labels (1 each for JIS/EN, 3 for FDA), ferrite cores (2), insure locks (2), instruction sheet

Model		ZS-LD130		ZS-LD200		ZS-LD350S
Applicable Controllers		ZS-HLDC/LDC series
Optical system		Diffuse reflection	Regular reflection	Diffuse reflection	Regular reflection	Diffuse reflection
Measuring center distance		130 mm	130 mm	200 mm	200 mm	350 mm
Measuring range		±15 mm	±12 mm	±50 mm	±48 mm	±135 mm
Light source		Visible semiconductor laser (wavelength: 650 nm, 1 mW max., JIS Class 2)
Beam shape		Line beam		Line beam		Spot beam
*Beam diameter 1**		600 × 70 μm		900 × 100 μm		240 μm dia.
*Linearity 2**		±0.1% FS	±0.25% FS	±0.1% FS	±0.25% FS	±0.1% FS
*Resolution 3**		3 μm		5 μm		20 μm
Temperature characteristic *4		0.02% FS/°C		0.02% FS/°C		0.04% FS/°C
Sampling cycle		110 μs (High-speed Mode), 500 μs (Standard Mode), 2.2 ms (High-precision Mode), 4.4 ms (High-sensitivity Mode)
LED Indicators	NEAR indicator	Lights near the measuring center distance, and closer than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
LED Indicators	FAR indicator	Lights near the measuring center distance, and farther than the measuring center distance inside the measuring range. Flashes when the measurement target is outside of the measuring range or when the received light amount is insufficient.
Operating ambient illumination		Illumination on received light surface: 2000 lx or less (incandescent light)		Illumination on received light surface: 3000 lx or less (incandescent light)
Ambient temperature		Operating: 0 to 50°C, Storage: -15 to 60°C (with no icing or condensation)
Ambient humidity		Operating and storage: 35% to 85% (with no condensation)
Degree of protection *5		Cable length 0.5 m: IP66, cable length 2 m: IP67
Materials		Case: Aluminum die-cast, Front cover: Glass
Cable length		0.5 m, 2 m
Weight		Approx. 350g
Accessories		Laser labels (1 each for JIS/EN, 3 for FDA), ferrite cores (2), insure locks (2), instruction sheet

∗1. Defined as 1/e2 (13.5%) of the center optical intensity at the actual measuring center distance (effective value).
The beam diameter is sometimes influenced by the ambient conditions of the workpiece, such as leaked light
from the main beam.
∗2. This is the error in the measured value with respect to an ideal straight line.
The standard workpiece is white aluminum ceramics and glass in the ZS-LD50/LD50S regular reflection mode.
Linearity may change according to the workpiece.
∗3. This is the peak-to-peak displacement conversion value in the displacement output at the measuring center
distance in high-precision mode when the number of samples to average is set to 128 and the measuring mode
is set to the high-resolution mode.
The standard workpiece is white aluminum ceramics and glass in the ZS-LD50/LD50S regular reflection mode.
∗4. This is the value obtained at the measuring center distance when the Sensor and workpiece are fixed by an
aluminum jig.
∗5. Protection structure of connector area is IP40.

ZS-MDC[]1 Multi-Controllers

Basic specifications are the same as those for the ZS-LDC[]1 Sensor Controllers. The following points, however, are different.
1. Sensor Heads cannot be connected.
2. Control Link Units are required to connect up to 9 Controllers.
Control Link Units are required to connect Controllers.
3. Processing functions between Controllers: Arithmetic functions

Controller Link Units

Connection Using the ZS-XCN

ZS-DSU[]1 Data Storage Unit

Model			ZS-DSU11	ZS-DSU41
Number of mounted Sensor Heads			Cannot be connected
Number of connectable Controllers			10 max. (ZS-MDC: 1, ZS-HLDC/LDC: 9 max.) *1
Connectable Controllers			ZS-HLDC[][], ZS-LDC[][], ZS-MDC[][]
External interface	Connection method		Serial I/O: connector, Other: pre-wired (standard cable length: 2 m)
	Serial I/O	USB 2.0	1 port, Full Speed (12 Mbps max.), MINI-B
	Serial I/O	RS-232C	1 port, 115,200 bps max.
	Output		3 outputs: HIGH, PASS, and LOW; NPN open-collector, 30 VDC, 50 mA max., residual voltage: 1.2 V max.	3 outputs: HIGH, PASS, and LOW; PNP open-collector, 50 mA max., residual voltage: 1.2 V max.
	Inputs		ON: Short-circuited with 0 V terminal or 1.5 V or less; OFF: Open (leakage current: 0.1 mA max.)	ON: Short-circuited to supply voltage or within 1.5 V of supply voltage; OFF: Open (leakage current: 0.1 mA max.)
Data resolution			32 bits
Functions	Logging trigger functions		Start and stop triggers can be set separately; external triggers, data triggers (self- triggers), and time triggers
Functions	Other functions		External banks, alarm outputs, saved data format customization, and clock
Status indicators			OUT (orange), PWR (green), ACCESS (orange), and ERR (red)
Segment display			8-segment green LEDs, 6 digits
LCD			16 digits x 2 rows, Color of characters: green, Resolution per character: 5 × 8 pixel matrix
Setting inputs	Setting keys		Direction keys (UP, DOWN, LEFT, and RIGHT), SET key, ESC key, MENU key, and function keys (1 to 4)
Setting inputs	Slide switch		Threshold switch (2 states: High/Low), mode switch (3 states: FUN, TEACH, and RUN)
Power supply voltage			21.6 V to 26.4 VDC (including ripple)
Current consumption			0.5 A max.
Ambient temperature			Operating: 0 to 50°C, Storage: 0 to 60°C (with no icing or condensation)
Ambient humidity			Operating and storage: 35% to 85% (with no condensation)
Degree of protection			IP20 (IEC60529)
Materials			Case: Polycarbonate (PC)
Weight			Approx. 280 g (excluding packing materials and accessories)
Accessories			Ferrite core (1), instruction sheet for Data Storage Unit: CSV File Converter for Data Storage Unit/Smart Analyzer Macro Edition

last update: June 01, 2015

Sensor Controllers

ZS-HLDC[]1/LDC[]1

Multi-Controllers

ZS-MDC[]1

Data Storage Units

ZS-DSU[]1

Sensor Heads

ZS-LD10GT

ZS-LD15GT

ZS-LD50/LD50S/LD80/LD130/LD200/LD350S

ZS-HLDS2VT/LD20T/LD20ST/LD40T

Realtime Parallel Output Unit

ZG-RPD[]1

Panel Mount Adapter

ZS-XPM1/XPM2 (Dimensions for Panel Mounting)

Please click image to enlarge (open in a new window).

Digital Equalizer

ZS-XEQ

Please click image to enlarge (open in a new window).

TITLE	DOCUMENT TYPE	SIZE
ZS Series Catalog	Catalog	4593 KB
ZS-CRT Sensor Communications Unit for Smart Sensors User's Manual	Manual	621 KB
ZS-DSU (Ver 2.0) Smart Sensor (Data Storage Unit) User's Manual	Manual	3655 KB
ZS-HL Series Smart Sensor (2D CMOS Laser Type) User's Manual	Manual	5707 KB
ZS-L Series (Ver 2.0) Smart Sensor (2D CMOS Laser Type) User's Manual	Manual	4826 KB
ZS-MDC (Ver 2.0) Smart Sensor (Multi-Controller) User's Manual	Manual	3330 KB
ZS Series Smart Sensors Non-procedual Communication Command Reference	Manual	1072 KB
ZS Series Smart Sensors CompoWay/F Communication Command Reference	Manual	1316 KB
ZG-RPD Smart Sensors Real-time Parallel Output Unit Instruction Sheet	Manual	968 KB
ZS-CRT Sensor Communication Unit for Smart Sensors Instruction Sheet	Manual	962 KB
ZS-DSU Smart Sensors Data Storage Unit Instruction Sheet	Manual	1016 KB
ZS-HLDC Smart Sensor Sensor Controller for ZS-HLD Instruction Sheet	Manual	789 KB
ZS-HLDS2(T) Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	659 KB
ZS-HLDS2V(T) Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	554 KB
ZS-HLDC Smart Sensor Sensor Controller for ZS-HLD Instruction Sheet	Manual	789 KB
ZS-HLDS3S(T) Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	921 KB
ZS-HLDS5(T) Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	620 KB
ZS-HLDS10 Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	663 KB
ZS-HLDS12AF(T) Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	926 KB
ZS-HLDS14AF(T) Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	599 KB
ZS-HLDS32 Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	843 KB
ZS-HLDS60/HLDS150 Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	915 KB
ZS-HLDS87 Sensor Head for Smart Sensor ZS-HLDC Instruction Sheet	Manual	897 KB
ZS-LD Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	745 KB
ZS-LD6GS(T) Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	558 KB
ZS-LD10(T) Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	924 KB
ZS-LD10G(T) Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	948 KB
ZS-LD15G/LD15GT Sensor Head for ZS-LDC Smart Sensor Instruction Sheet	Manual	10257 KB
ZS-LD20/LD40 Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	1221 KB
ZS-LD20S(T) Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	781 KB
ZS-LD20T/LD40T Sensor Head for ZS-LDC Smart Sensor Instruction Sheet	Manual	12147 KB
ZS-LD35AF(T) Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	912 KB
ZS-LD40-N Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	1257 KB
ZS-LD50-1 Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	930 KB
ZS-LD50S Sensor Head for ZS-LDC Smart Sensor Instruction Sheet	Manual	12426 KB
ZS-LD50SR Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	1110 KB
ZS-LD350S Sensor Head for Smart Sensor ZS-LDC Instruction Sheet	Manual	770 KB
ZS-LDC Smart Sensor for ZS-LDC Sensor Controller Instruction Sheet	Manual	18638 KB
ZS-MDC Smart Sensor Multi-Controller Instruction Sheet	Manual	19622 KB
ZS-RPD Smart Sensors Real-time Parallel Output Unit Instruction Sheet	Manual	993 KB
ZS-XC-A Extension Cable Instruction Sheet	Manual	4056 KB
ZS-XC-B-R Extension Cable Instruction Sheet	Manual	4286 KB
ZS-XC-CR Smart Sensors Long-distance Extension Cable Instruction Sheet	Manual	561 KB
ZS-XC02D Smart Sensor Conversion Cable for Connecting Digital Equalizer to Sensor Controller Instruction Sheet	Manual	527 KB
ZS-XC5BR-1 Extension Cable Instruction Sheet	Manual	704 KB
ZS-XCN Controller Link Unit Instruction Sheet	Manual	8214 KB
ZS-XEQ Smart Sensor Digital Equalizer Instruction Sheet	Manual	443 KB
ZS-XPM1/XPM2 Panel Mount Adapter Instruction Sheet	Manual	3534 KB
ZS-XPT RS-232C Cable for Connecting to a Programmable Controller/Programmable Terminal Instruction Sheet	Manual	3814 KB
ZS-XRS RS-232C Cable for Connecting to a Personal Computer Instruction Sheet	Manual	2778 KB

ZS-HL Series

Very High-performance Sensors that Support Core Quality from Very Long-range to Extremely Precise Measurements

All Models Are Class 2 Lasers.

Extreme Stability

Ideal Size and Stability
Head Size

Superior Moving Resolution
Increased Lens Resolution

Reduced Error for Different Materials
2D CMOS

ZS-L Series

Standard Sensors Most Suitable for a Variety of High-precision Displacement Measurements, Including Spot Detection, Wide-range Detection, and Long-distance Detection.

ZS-HL/L-series Sensor Controllers

ZS-HL-series Sensor Heads

ZS-L-series Sensor Heads

ZS-L-series Sensor Heads

ZS-MDC[]1 Multi-Controllers

Controller Link Units

ZS-DSU[]1 Data Storage Unit

Sensor Controllers

ZS-HLDC[]1/LDC[]1

Multi-Controllers

ZS-MDC[]1

Data Storage Units

ZS-DSU[]1

Sensor Heads

ZS-HLDS2T

ZS-HLDS5T/HLDS10

ZS-HLDS60/HLDS150

ZS-LD10GT

ZS-LD15GT

ZS-LD50/LD50S/LD80/LD130/LD200/LD350S

ZS-HLDS2VT/LD20T/LD20ST/LD40T

Realtime Parallel Output Unit

ZG-RPD[]1

Panel Mount Adapter

ZS-XPM1/XPM2 (Dimensions for Panel Mounting)

Digital Equalizer

ZS-XEQ

Group Sites

Our Partner Sites

Subscribe Our Newsletter

ZS-HL Series

Very High-performance Sensors that Support Core Quality from Very Long-range to Extremely Precise Measurements

All Models Are Class 2 Lasers.

Extreme Stability

Ideal Size and Stability Head Size

Superior Moving Resolution Increased Lens Resolution

Reduced Error for Different Materials 2D CMOS

ZS-L Series

Standard Sensors Most Suitable for a Variety of High-precision Displacement Measurements, Including Spot Detection, Wide-range Detection, and Long-distance Detection.

ZS-HL/L-series Sensor Controllers

ZS-HL-series Sensor Heads

ZS-L-series Sensor Heads

ZS-L-series Sensor Heads

ZS-MDC[]1 Multi-Controllers

Controller Link Units

ZS-DSU[]1 Data Storage Unit

Sensor Controllers

ZS-HLDC[]1/LDC[]1

Multi-Controllers

ZS-MDC[]1

Data Storage Units

ZS-DSU[]1

Sensor Heads

ZS-HLDS2T

ZS-HLDS5T/HLDS10

ZS-HLDS60/HLDS150

ZS-LD10GT

ZS-LD15GT

ZS-LD50/LD50S/LD80/LD130/LD200/LD350S

ZS-HLDS2VT/LD20T/LD20ST/LD40T

Realtime Parallel Output Unit

ZG-RPD[]1

Panel Mount Adapter

ZS-XPM1/XPM2 (Dimensions for Panel Mounting)

Digital Equalizer

ZS-XEQ

Ideal Size and Stability
Head Size

Superior Moving Resolution
Increased Lens Resolution

Reduced Error for Different Materials
2D CMOS