Omron, EE-SX95 Series

Mount Using M2 or M3 Screws

The EE-SX95 can be mounted using M2 or M3 screws, so it can easily replace an existing Sensor mounted with M2 screws.

Reliable Best-in-Class Sensing Slot Depth of 6.5 mm

(Based on April 2013 OMRON investigation.)
A deeper slot helps prevent the sensing object from coming into contact with the base of the slot, creating greater tolerance in mechanism design.

Indication of Sensing Window for Easy Confirmation of Insertion Depth

The location of the sensing window is indicated on the insertion slot so that you can visually confirm whether the sensing object covers the sensing window and easily check the insertion depth.

Bright Indicator for Confirmation from Many Directions

The bright light indicator can be checked from up to four directions to enable flexible selection of the installation location.

last update: March 02, 2015

Type		Standard	L-shaped	F-shaped	R-shaped	U-shaped
NPN output	Pre-wired models	EE-SX950-[]	EE-SX951-[]	EE-SX952-[]	EE-SX953-[]	EE-SX954-[]
NPN output	Pre-wired connector models	EE-SX950-C1J-R	EE-SX951-C1J-R	EE-SX952-C1J-R	EE-SX953-C1J-R	EE-SX954-C1J-R
PNP output	Pre-wired models	EE-SX950P-[]	EE-SX951P-[]	EE-SX952P-[]	EE-SX953P-[]	EE-SX954P-[]
Sensing distance		5 mm (slot width)
Standard sensing object		Opaque: 1.8 × 0.8 mm min.
Differential travel		0.025 mm max. *1
Light source (wave length)		Infrared LED (940 nm)
Indicator		Light indicator (red LED)
Power supply voltage		5 to 24 VDC ±10%, ripple (p-p): 10% max.
Current consumption		15 mA max.
Control output		Load power supply voltage: 5 to 24 VDC Load current: 50 mA max. OFF current: 0.5 mA max. 50 mA load current with a residual voltage of 0.7 V max. 5 mA load current with a residual voltage of 0.4 V max.
Protection circuit		Load short-circuit protection
Response frequency		1 kHz min. (3 kHz average) *2
Ambient illumination		1,000 lx max. with fluorescent light on the surface of the receiver
Ambient temperature range		Operating: -25 to 55°C Storage: -30 to 80°C (with no icing or condensation)
Ambient humidity range		Operating: 5% to 85% Storage: 5% to 95% (with no icing or condensation)
Vibration resistance (destruction)		10 to 2,000 Hz (peak acceleration: 150m/s²) with a 0.75-mm single amplitude for 2.5 h (15-min periods, 10 cycles) each in X, Y, and Z directions
Shock resistance (destruction)		500 m/s² for 3 times each in X, Y, and Z directions
Degree of protection		IEC60529 IP50
Connection method		Pre-wired models (standard length: 1 m), Pre-wired connector models (standard length: 0.3 m)
Weight (packed state)	Pre-wired models	Approx. 15 g
Weight (packed state)	Pre-wired connector models	Approx. 7 g
Materials	Case/cover	Polybutylene terephthalate (PBT)
Materials	Emitter/ receiver	Polycarbonate (PC)

*1. The differential travel is the value when a sensing object is moved in a lateral direction to the slot.
*2. The response frequency was measured by detecting the following rotating disk.

Applicable Connector

Product		Connector with Robot Cable
Model		EE-1016-R
Appearance
Contact resistance		25 mΩ max. (at 10 mA DC and 20 mV max.)
Insertion strength		20 N max.
Surplus strength (housing holding strength)		15 N min.
Cable length		2 m
Ambient temperature range		-25 to 85°C
Materials	Housing	Nylon
Materials	Contact	Phosphor bronze

last update: March 02, 2015

Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.

Sensors

EE-SX950-[]
EE-SX950P-[]
EE-SX950-C1J-R

EE-SX951-[]
EE-SX951P-[]
EE-SX951-C1J-R

EE-SX952-[]
EE-SX952P-[]
EE-SX952-C1J-R

EE-SX953-[]
EE-SX953P-[]
EE-SX953-C1J-R

EE-SX954-[]
EE-SX954P-[]
EE-SX954-C1J-R

Accessories (Order Separately)

Connector with Robot Cable

EE-1016-R

TITLE	DOCUMENT TYPE	SIZE
EE-SX95 Data Sheet	Catalog	1540 KB
EE-SX95 Compact Pre-wired Photomicrosensor with Amplifier (Non-modulated) Instruction Sheet	Manual	738 KB