Power rating			15 W	30 W	50 W	100 W	150 W
Efficiency		5-V models	75% min.	75% min.	80% min.	81% min.	81% min.
		12-V models	78% min.	79% min.	79% min.	81% min.	81% min.
		15-V models	78% min.	79% min.	79% min.	81% min.	81% min.
		24-V models	80% min.	81% min.	80% min.	82% min.	83% min.
Input	Voltage *1		100 to 240 VAC (85 to 265 VAC)
	Frequency *1		50/60 Hz (47 to 63 Hz)
	Current	100-V input	0.5 A max.	0.9 A max.	0.8 A max.	1.4 A max.	2.0 A max.
		200-V input	0.25 A max.	0.45 A max.	0.4 A max.	0.7 A max.	1.0 A max.
	Power factor	100-V input	---		0.98 min.
		200-V input	---		0.94 min.
	Harmonic current emissions		---		Conforms to EN 61000-3-2
	Leakage current	100-V input	0.4 mA max. (at rated output)
		200-V input	0.75 mA max. (at rated output)
	Inrush current *2	100-V input	17.5 A max. (for cold start at 25 °C)
		200-V input	35 A max. (for cold start at 25 °C)
Output	Voltage adjustment range *3		-20% to 20% (with V. ADJ) (S8VM-[][][]24A[]/P[]: -10% to 20%)
	Ripple		3.2% (p-p) max. (5 V), 1.5% (p-p) max. (12 V), 1.2% (p-p) max. (15 V), 1.0% (p-p) max. (24 V), (at rated input/output voltage)		3.2% (p-p) max. (5 V), 1.5% (p-p) max. (12 V), 1.2% (p-p) max. (15 V), 0.75% (p-p) max. (24 V), (at rated input/output voltage)
	Input variation influence		0.4% max. (at 85 to 265 VAC input, 100%)
	Load variation influence (rated input voltage)		0.8% max. (with rated input, 0 to 100% load)
	Temperature variation influence		0.02%/°C max.
	Startup time *2		1,100 ms max. (at rated input/output voltage)		800 ms max. (at rated input/output voltage)
	Hold time *2		20 ms typ. (15 ms min.) (at rated input/output voltage)
Additional functions	Overload protection *2		105% to 160% of rated load current, voltage drop, intermittent, automatic reset		105% to 160% of rated load current, voltage drop (12 V, 15 V, and 24 V), voltage drop, intermittent (5 V), automatic reset
	Overvoltage protection *2		Yes *4
	Undervoltage alarm indication		Yes (color: Yellow (DC LOW1), red (DC LOW2)) (S8VM-[][][]24A[]/P[] only)
	Undervoltage alarm output		No		Yes (S8VM-[][][]24A[]/P[] only) (Transistor output), 30 VDC max., 50 mA max. *8
	Series operation		Yes for up to 2 Power Supplies (with external diode)
	Parallel operation		No (However, backup operation is possible. An external diode is required.)
	Remote sensing function		No			Yes
Other	Ambient operating temperature		Refer to the derating curve in See Engineering Data on Data Sheet (15-W, 30-W, 50-W, 100-W, 150-W Models). (with no icing or condensation) *2
	Storage temperature		-25 to 65°C
	Ambient operating humidity		30% to 85% (Storage humidity: 25% to 90%)
	Dielectric strength		3.0 kVAC for 1 min. (between all inputs and outputs; detection current: 20 mA) 2.0 kVAC for 1 min. (between all inputs and PE/FG terminals; detection current: 20 mA) 500 VAC for 1 min. (between all outputs and PE/FG terminals; detection current: 100 mA) 500 VAC for 1 min. (between all outputs (except the detection output terminals) and detection output terminals; detection current: 20 mA) (S8VM- [][][]24A[]/P[] only)
	Insulation resistance		100 MΩ min. (between all outputs and all inputs, PE/FG terminals) at 500 VDC
	Vibration resistance		10 to 55 Hz, 0.375-mm single amplitude for 2 hours each in X, Y, and Z directions
	Shock resistance		150 m/s2, 3 times each in ±X, ±Y, ±Z directions
	Output indicator		Yes (color: Green)
	EMI	Conducted Emission	Conforms to EN55011 Group1 Class B and based on FCC Class B *5
		Radiated Emission	Conforms to EN55011 Group1 Class B *6
	EMS		Conforms to EN61204-3 High severity levels
	Approved standards	UL	UL508 (Listing), UL60950-1
		cUL	CSA C22.2 No.14
		cUR	CSA No. 60950-1
		EN/TÜV	EN50178, EN60950-1 SELV (EN60950-1) According to VDE0160/P100
		SEMI	SEMI F47-0200 (200 VAC input)
	Weight *7		180 g max.	220 g max.	290 g max.	460 g max.	530 g max.

Power rating			300 W	600 W	1,500 W
Efficiency		5-V models	77% min.	77% min.	---
		12-V models	78% min.	79% min.	---
		15-V models	79% min.	80% min.	---
		24-V models	81% min.	81% min.	82% min.
Input	Voltage *1		100 to 240 VAC (85 to 265 VAC)		100 to 240 VAC (85 to 265 VAC)
	Frequency *1		50/60 Hz (47 to 63 Hz)
	Current	100-V input	4.0 A max. (5 V) 4.3 A max. (12 V, 15 V, and 24 V)	8.0 A max. (5 V) 8.3 A max. (12 V, 15 V, and 24 V)	20.0 A max.
		200-V input	2.0 A max. (5 V) 2.2 A max. (12 V, 15 V, and 24 V)	4.0 A max. (5 V) 4.2 A max. (12 V, 15 V, and 24 V)	11.0 A max.
	Power factor	100-V input	0.98 min.		0.97 min.
		200-V input	0.94 min.		0.93 min.
	Harmonic current emissions		Conforms to EN61000-3-2
	Leakage current	100-V input	0.4 mA max.		1.5 mA max.
		200-V input	0.75 mA max.		1.5 mA max.
	Inrush current *2	100-V input	20 A max. (for cold start at 25 °C)
		200-V input	40 A max. (for cold start at 25 °C)
Output	Voltage adjustment range *3		-20% to 20% (with V. ADJ)
	Ripple		3.8% (p-p) max. (5 V), 2.0% (p-p) max. (12 V), 2.0% (p-p) max. (15 V), 1.25% (p-p) max. (24 V), (at rated input/output voltage)		1.25% (p-p) max. *7, (at rated input/output voltage)
	Input variation influence		0.4% max. (at 85 to 265 VAC input, 100%)
	Load variation influence (rated input voltage)		0.6% max. (with rated input, 0 to 100% load)
	Temperature variation influence		0.02%/°C max.
	Startup time *2		1,000 ms max. (at rated input/output voltage)
	Hold time *2		20 ms typ. (15 ms min.) (at rated input/output voltage)
Additional functions	Overload protection *2		105% to 160% of rated load current (5 V, 12 V, and 15 V), 120% to 160% of rated load current (S8VM-30024C), 115% to 160% of rated load current (S8VM- 60024C), voltage drop (12 V, 15 V, and 24 V), voltage drop, intermittent (5 V), automatic reset		105% to 160% of rated load current (100 VAC), 155% to 200% of rated load current (200 VAC), voltage drop, automatic reset (Turns OFF when continuous for 5 s min.) *4
	Overvoltage protection *2		Yes *4
	Overheat protection *2		Yes *4
	Undervoltage alarm indication		No
	Undervoltage alarm output		No
	Power failure alarm indication		Yes (color: Red)
	Power failure alarm output		Yes (Transistor output), 30 VDC max., 50 mA max.
	Series operation		Yes for up to 2 Power Supplies (with external diode)
	Parallel operation		Yes (up to 2 units)
	Remote sensing function		Yes
	Remote control function		Yes
Other	Ambient operating temperature		Refer to the derating curve in See Engineering Data on Data Sheet (300-W, 600-W, 1,500-W Models). (with no icing or condensation) *2
	Storage temperature		-25 to 65°C
	Ambient operating humidity		30% to 85% (Storage humidity: 25% to 90%)
	Dielectric strength		3.0 kVAC for 1 min. (between all inputs and outputs; detection current: 20 mA) 2.0 kVAC for 1 min. (between all inputs and PE terminals; detection current: 20 mA) 500 VAC for 1 min. (between all outputs and PE terminals; detection current: 100 mA) 100 VAC for 1 min. (between all outputs and RC terminals; detection current: 100 mA) 500 VAC for 1 min. (between all outputs and PF terminals; detection current: 20 mA)		3.0 kVAC for 1 min. (between all inputs and outputs; detection current: 20 mA) 2.0 kVAC for 1 min. (between all inputs and FG terminals; detection current: 20 mA) 500 VAC for 1 min. (between all outputs and FG terminals; detection current: 300 mA) 100 VAC for 1 min. (between all outputs and RC terminals; detection current: 100 mA) 500 VAC for 1 min. (between all outputs and PF terminals; detection current: 20 mA)
	Insulation resistance		100 MΩ min. (between all outputs and all inputs, PE terminals) at 500 VDC		100 MΩ min. (between all outputs and all inputs, FG terminals) at 500 VDC
	Vibration resistance		10 to 55 Hz, 0.375-mm single amplitude for 2 hours each in X, Y, and Z directions		10 to 55 Hz, 0.15-mm single amplitude for 2 hours each in X, Y, and Z directions
	Shock resistance		150 m/s2, 3 times each in ±X, ±Y, ±Z directions
	Output indicator		Yes (color: Green)
	EMI	Conducted Emission	Conforms to EN55011 Group1 Class B and based on FCC Class B *5		Conforms to EN55011 Group1 Class A and based on FCC Class A *6
		Radiated Emission	Conforms to EN55011 Group1 Class B *5		Conforms to EN55011 Group1 Class A *6
	EMS		Conforms to EN61204-3 High severity levels
	Approved standards *8	UL	UL508 (Recognition) (5 V, 12 V, and 15 V) UL508 (Listing) (24 V), UL60950-1		UL508, UL60950-1
		cUR	CSA C22.2 No.14 (24 V)
		cUR	CSA No. 60950-1		CSA C22.2 No.14, CSA No. 60950-1
		EN/TÜV	EN50178, EN60950-1 SELVE (EN60950-1)		EN50178, EN60950-1 SELVE (EN60950-1)
		SEMI	SEMI F47-0200 (200-VAC input)
	Weight		1,100 g max.	1,700 g max.	3,800 g max.

*1. Do not use an Inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available,
       but the rise in the internal temperature of the Power Supply may result in ignition or burning.
*2. Refer to Engineering Data (300-W, 600-W, 1,500-W Models) on Catalog for details.
*3. If the output voltage adjuster (V. ADJ) is turned, the voltage will increase by more than +20% of the voltage
       adjustment range. If the adjuster is turned too far, it may activate the overvoltage protection function and interrupt
       the output. When adjusting the output voltage, confirm the actual output voltage from the Power Supply and be
       sure that the load is not damaged.
*4. To reset the protection, turn OFF the input power for three minutes or longer and then turn it back ON. Alternatively,
       turn OFF the remote control signal and then turn it back ON again.
*5. Conducted emissions: The noise value is affected by factors such as the wiring method. The Power Supply conforms
       to Class B when the aluminum plate is laid under the Power Supply. For 600-W models, insert a clamp filter
       (ZCAT3035-1330 by TDK: 100 Ω min. [50 to 500 MHz], or the equivalent) in the input wire, and ring core
       (HF60T38X14X22 by TDK: 16 Ω typ. [1 MHz], 46 Ω typ. [10 MHz], or the equivalent) in the output wire to reduce
       noise
*6. Radiated emissions: The noise value is affected by factors such as the wiring method. The Power Supply conforms to
       Class A when the aluminum plate is laid under the Power Supply (1,500-W models).
*7. The measuring method conforms to JEITA standard RC-9131A. Refer to Ripple under Safety Precautions on Catalog.
*8. The Power Supply will not conform to safety standards if the customer replaces the fan.