Omron, G7SA Series

last update: October 3, 2016

• Additional Push-In Plus terminal sockets are used to save wiring work in comparison with traditional screw terminals. ( Wiring time is reduced by 60%* in comparison with traditional screw terminals. )

• Relays with forcibly guided contacts (EN 50205 Class A, certified by VDE).

• Supports the CE marking of machinery (Machinery Directive).

• Helps avoid hazardous machine status when used as part of an interlocking circuit.

• Four-pole and six-pole Relays are available.

• The Relay’s terminal arrangement simplifies PWB pattern design.

• Reinforced insulation between inputs and outputs. Reinforced insulation between some poles of different polarity.

* According to OMRON actual measurement data

last update: October 3, 2016

last update: April 6, 2017

Ratings

Coil (4 poles)

Item	Rated current (mA)	Coil resistance (Ω)	Max. voltage (V)	Power consumption (mW)
Rated voltage	Rated current (mA)	Coil resistance (Ω)	Max. voltage (V)	Power consumption (mW)
12 VDC	30	400	110%	Approx. 360
18 VDC	20	900
21 VDC	17.1	1,225
24 VDC	15	1,600
48 VDC	7.5	6,400
110 VDC	3.8	28,810		Approx. 420

Coil (6 poles)

Item	Rated current (mA)	Coil resistance (Ω)	Max. voltage (V)	Power consumption (mW)
Rated voltage	Rated current (mA)	Coil resistance (Ω)	Max. voltage (V)	Power consumption (mW)
12 VDC	41.7	288	110%	Approx. 500
18 VDC	27.8	648
21 VDC	23.8	882
24 VDC	20.8	1,152
48 VDC	10.4	4,606
110 VDC	5.3	20,862		Approx. 580

Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with tolerances of ±15%.
2. The maximum voltage is based on an ambient operating temperature of 23°C maximum.

Contacts

Load	Resistive load
Rated load	6 A at 250 VAC, 6 A at 30 VDC
Rated carry current	6 A
Max. switching voltage	250 VAC, 125 VDC
Max. switching current	6 A
Contact materials	Au plating + Ag alloy

Characteristics

*Contact resistance 1**		100 mΩ max.
*Operating time 2**		20 ms max.
*Response time 3**		10 ms max.
*Release time 2**		20 ms max.
Must operate voltage		75% max.
Must release voltage		10% min.
Maximum operating frequency	Mechanical	36,000 operations/h
Maximum operating frequency	Rated load	1,800 operations/h
*Insulation resistance 4**		1,000 MΩ min.
Dielectric Strength 5 6	Between coil and contacts	4,000 VAC, 50/60 Hz for 1 min.
	Between contacts of different polarity	4,000 VAC, 50/60 Hz for 1 min. (except for followings) 4 poles (for poles 3-4 in 4-pole Relays), 6 poles (for poles 3-5, 4-6, and 5-6 in 6-pole Relays): 2,500 VAC, 50/60 Hz for 1 min.
	Between contacts of the same polarity	1,500 VAC, 50/60 Hz for 1 min.
Vibration resistance		10 to 55 to 10 Hz, 0.75-mm single amplitude (1.5-mm double amplitude)
Shock resistance	Destruction	1,000 m/s²
Shock resistance	Malfunction	100 m/s²
Durability *7	Mechanical	10,000,000 operations min. (at approx. 36,000 operations/h)
Durability *7	Electrical	100,000 operations min. (at the rated load and approx. 1,800 operations/h)
Inductive load switching capability *8 (IEC60947-5-1)		AC15 AC240V 2A DC13 DC24V 1A
Failure rate (P level) (reference value *9)		5 VDC, 1 mA
Ambient operating temperature *10		12 to 48 VDC: -40 to 85°C (with no icing or condensation) 110 VDC: -40 to 60°C (with no icing or condensation)
Ambient operating humidity		5% to 85%
Weight		4 poles: Approx. 22 g 6 poles: Approx. 25 g

Note: 1. The above values are initial values.
2. Performance characteristics are based on coil temparature of 23°C.
*1. The contact resistance was measured with 1 A at 5 VDC using the voltage-drop method.
*2. These times were measured at the rated voltage and an ambient temperature of 23°C. Contact bounce time is not included.
*3. The response time is the time it takes for the normally open contacts to open after the coil voltage is turned OFF. Contact bounce time is included. Measurement conditions: Rated voltage operation, Ambient temperature: 23°C
*4. The insulation resistance was measured with a 500-VDC megohmmeter at the same locations as the dielectric strength was measured.
*5. Pole 3 refers to terminals 31-32 or 33-34, pole 4 refers to terminals 43-44, pole 5 refers to terminals 53-54, and pole 6 refers to terminals 63-64.
*6. When using a P7SA Socket, the dielectric strength between coil contacts/different poles is 2,500 VAC, 50/60 Hz for 1 min. When using Push-In Plus terminal sockets (P7SA-[]F-ND-PU), the dielectric strength between coil contacts as well as between different poles is 4,000 VAC, 50/60 Hz for 1 min.
*7. The durability is for an ambient temperature of 15 to 35°C and an ambient humidity of 25% to 75%. For the durability performance to the load, refer to the durability Curve.
*8. AC15: cosφ = 0.3, DC13: L/R = 48-ms.
*9. The failure rate is based on an operating frequency of 300 operations/min.
*10. 12 to 48 VDC:
When operating between 70 and 85°C, reduce the rated carry current of 6 A by 0.1 A for each degree above 70°C.
110 VDC:
When operating between 40 and 60°C, reduce the rated carry current of 6 A by 0.27 A for each degree above 40°C.

Characteristics of Sockets

Model		Push-In Plus terminals		Screw terminals		PCB terminals
		4 poles	6 poles	4 poles	6 poles	4 poles	6 poles
		P7SA-10F-ND-PU	P7SA-14F-ND-PU	P7SA-10F(-ND)	P7SA-14F(-ND)	P7SA-10P	P7SA-14P
Ambient operating temperature		• With operation indicator LED/built-in diode 　P7SA-[]F-ND(-PU): -20 to +70°C • Without operation indicator LED/built-in diode 　P7SA-[]F: -40 to +85°C (with no icing or condensation)				-40 to +85°C (with no icing or condensation)
Ambient operating humidity		25% to 85%				5% to 85%
Continuous carry current		6 A *1
Dielectric strength	Between coil and contact terminals	4,000 VAC for 1 min.	2,500 VAC for 1 min.
	Between contact terminals of different polarity	2,500 VAC for 1 min.	2,500 VAC for 1 min.
	Between contact terminals of same polarity	1,500 VAC for 1 min.
Insulation resistance		1,000 MΩ min. *2
Weight		Approx. 58 g	Approx. 70 g	Approx. 44 g	Approx. 59 g	Approx. 9 g	Approx. 10 g

*1. When operating the P7SA-[]F-ND-PU at a temperature between 50 and 70°C, reduce the continuous current
(6 A at 50°C or less) by 0.25 A for each degree above 50°C.
When operating the P7SA-[]F-ND at a temperature between 50 and 70°C, reduce the continuous current
(6 A at 50°C or less) by 0.3 A for each degree above 50°C.
When operating the P7SA-[]F at a temperature between 50 and 85°C, reduce the continuous current
(6 A at 50°C or less) by 0.1 A for each degree above 50°C.
*2. Measurement conditions: For 500 VDC applied to the same location as for dielectric strength measurement.

last update: April 6, 2017

Relays with Forcibly Guided Contacts

4 poles
G7SA-3A1B
G7SA-2A2B

6 poles
G7SA-5A1B
G7SA-4A2B
G7SA-3A3B

Sockets

Front-mounting Sockets

Push-In Plus terminals 4 poles
P7SA-10F-ND-PU

Push-In Plus terminals 6 poles
P7SA-14F-ND-PU

Accessories (Order Separately)

Short Bars (for P7SA-[]F-ND-PU)

XW5S-P2.5-[][]

Please click image to enlarge (open in a new window).

Front-mounting Sockets

Screw terminals 4 poles
P7SA-10F, P7SA-10F-ND

Please click image to enlarge (open in a new window).

Screw terminals 6 poles
P7SA-14F, P7SA-14F-ND

Please click image to enlarge (open in a new window).

Accessories (Order Separately)

Parts for DIN Track Mounting

Refer to your OMRON website for details about PFP-[].

Back-mounting Sockets (for PCB)

PCB terminals 4 poles
P7SA-10P

PCB terminals 6 poles
P7SA-14P

TITLE	DOCUMENT TYPE	SIZE
G7SA Data Sheet	Catalog	2381 KB
Push-In Plus Terminal Block Series Pamphlet	Catalog	7307 KB
Innovation in Control Panel Building	Catalog	13592 KB

Ratings

Coil (4 poles)

Coil (6 poles)

Contacts

Characteristics

Characteristics of Sockets

Relays with Forcibly Guided Contacts

Sockets

Front-mounting Sockets

Accessories (Order Separately)

Short Bars (for P7SA-[]F-ND-PU)

Front-mounting Sockets

Accessories (Order Separately)

Parts for DIN Track Mounting

Back-mounting Sockets (for PCB)

Group Sites

Our Partner Sites

Subscribe Our Newsletter