Omron, G7J Series

• Miniature hinge for maximum switching power for motor loads as well as resistive and inductive loads.

• No contact chattering for momentary voltage drops up to 50% of rated voltage.

• Withstanding more than 4 kV between contacts that are different in polarity and between the coil and contacts.

• Flame-resistant materials (UL94V-0-qualifying) used for all insulation material.

• Standard models approved by UL and CSA.

Coil Ratings

Rated voltage		Rated current	Coil resistance	Must-operate voltage	Must-release voltage	Max. voltage	Power consumption
AC	24 VAC	75 mA	---	75% max. of rated voltage	15% min. of rated voltage	110% of rated voltage	Approx. 1.8 to 2.6 VA
	50 VAC	36 mA	---
	100 to 120 VAC	18 to 21.6 mA	---
	200 to 240 VDC	9 to 10.8 mA	---
DC	12 VDC	167 mA	72 Ω		10% min. of rated voltage		Approx. 2.0 W
	24 VDC	83 mA	288 Ω
	48 VDC	42 mA	1,150 Ω
	100 VDC	20 mA	5,000 Ω

Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with tolerances of +15%/-20% for AC rated current and ±15% for DC coil resistance. (The values given for AC rated current apply at 50 Hz or 60 Hz.)
2. Performance characteristic data are measured at a coil temperature of 23°C.
3. The maximum voltage is one that is applicable to the Relay coil at 23°C.

Contact Ratings

Rated load			NO: 25 A at 30 VDC NC: 8 A at 30 VDC
Item	Resistive load (cosΦ = 1)	Inductive load (cosΦ = 0.4)	Resistive load
Contact mechanism	Double break
Contact material	Ag alloy
Rated load	NO: 25 A at 220 VAC (24 A at 230 VAC) NC: 8 A at 220 VAC (7.5 A at 230 VAC)		NO: 25 A at 30 VDC NC: 8 A at 30 VDC
Rated carry current	NO: 25 A (1 A) NC: 8 A (1 A)
Rated carry current	NO: 25 A (1 A) NC: 8 A (1 A)
Max. switching voltage	250 VAC		125 VDC
Max. switching current	NO: 25 A (1 A) NC: 8 A (1 A)
Max. switching current	NO: 25 A (1 A) NC: 8 A (1 A)

Note: The values in parentheses indicate values for a bifurcated contact.

Characteristics

*Contact resistance 2**	100 mΩ max.
*Operate time 3**	50 ms max.
*Release time 3**	50 ms max.
Max. operating frequency	Mechanical: 1,800 operations/hr Electrical: 1,800 operations/hr
*Insulation resistance 4**	1,000 MΩ min. (at 500 VDC)
Dielectric strength	4,000 VAC, 50/60 Hz for 1 min between coil and contacts 4,000 VAC, 50/60 Hz for 1 min between contacts of different polarity 2,000 VAC, 50/60 Hz for 1 min between contacts of same polarity
Impulse withstand voltage	10,000 V between coil and contact (with 1.2 x 50 μs impulse wave)
Vibration resistance	Destruction: 10 to 55 to 10 Hz, 0.75-mm single amplitude (1.5-mm double amplitude) Malfunction: NO: 10 to 55 to 10 Hz, 0.75-mm single amplitude (1.5-mm double amplitude) NC: 10 to 26 to 10 Hz, 0.75-mm single amplitude (1.5-mm double amplitude)
Shock resistance	Destruction: 1,000 m/s² Malfunction: NO: 100 m/s², NC: 20 m/s²
Endurance	Mechanical: 1,000,000 operations min. (at 1,800 operations/hr) Electrical: 100,000 operations min. (at 1,800 operations/hr) *5
*Error rate 6**	100 mA at 24 VDC (bifurcated contact: 24 VDC 10 mA)
Ambient temperature	Operating: -25°C to 60°C (with no icing or condensation)
Ambient humidity	Operating: 5% to 85%
Weight	PCB terminal: approx. 140 g Screw terminal: approx. 165 g Quick-connect terminal:approx. 140 g

*1. The above values are all initial values.
*2. The contact resistance was measured with 1 A at 5 VDC using the voltage drop method.
*3. The operate and the release times were measured with the rated voltage imposed with any contact bounce ignored
at an ambient temperature of 23°C.
*4. The insulation resistance was measured with a 500-VDC megger applied to the same places as those used for
checking the dielectric strength.
*5. The electrical endurance was measured at an ambient temperature of 23°C.
*6. This value was measured at a switching frequency of 60 operations per minute.

Screw Terminals with W-bracket
G7J-4A-B, G7J-3A1B-B, G7J-3A1B-BZ, G7J-2A2B-B

Quick-connect Terminals with W-bracket
G7J-4A-T, G7J-4A-TZ, G7J-3A1B-T, G7J-2A2B-T

PCB Terminals with PCB Mounting
G7J-4A-P, G7J-4A-PZ, G7J-3A1B-P, G7J-3A1B-PZ, G7J-2A2B-P

Terminal Arrangement/Internal Connections

Note: Terminals 43 and 44 of the G7J-4A-P(T) and contacts 41 and 42 of the G7J-3A1B-P(B) are bifurcated contacts.

Accessories (Order Separately)

R99-04 W-bracket (for G5F)

TITLE	DOCUMENT TYPE	SIZE
G7J	Catalog	854 KB
Relay Defects Causes & Solutions (General-purpose Relay Edition)	Technical Guide	4100 KB

Coil Ratings

Contact Ratings

Characteristics

Terminal Arrangement/Internal Connections

Accessories (Order Separately)

Group Sites

Our Partner Sites

Subscribe Our Newsletter