Omron, E3NW Series

last update: April 04, 2013

Introduction

Radically Reduce Manufacturing Costs

Even if you implement a Sensor Network, the cost of introduction is greatly reduced.

Please click image to enlarge (open in a new window).

Greatly Reduce Introduction Cost in Comparison to Previous Sensor Networks

Please click image to enlarge (open in a new window).

Commissioning

Radically Reduce System Commissioning Time

Easy Batch Setting from a Touch Panel

Please click image to enlarge (open in a new window).

Line Changeovers Are Also Easy with a Setup Backup Function

Please click image to enlarge (open in a new window).

Operation

Radically Increase Machine Productivity

Monitoring for Predictive Maintenance

Please click image to enlarge (open in a new window).

You can use E3NW communications to create controller programming or touch panel displays to perform all of the settings and monitoring that are described on Catalog.
Display samples for OMRON NS-series Programmable Terminals (touch panels) and sample programming for OMRON NJ-series Controllers are available.
For details, please contact your OMRON sales representative.

Reduced Downtime When Troubles Occur

Please click image to enlarge (open in a new window).

last update: April 04, 2013

Sensor Communications Unit

EtherCAT

Model	E3NW-ECT
Connectable Sensor Amplifier Units	N-Smart Smart Fiber Amplifier Unit: E3NX-FA0 Color Fiber Amplifier Unit: E3NX-CA0 1 Smart Laser Amplifier Unit: E3NC-LA0 Smart Laser Amplifier Unit (CMOS type): E3NC-SA0 Contact-Type Smart Amplifier Unit: E9NC-TA0 2
Power supply voltage	24 VDC (20.4 to 26.4 V)
Power and current consumption	2.4 W max. (Not including the power supplied to Sensors.), 100 mA max. (Not including the current supplied to Sensors.)
Indicators	L/A IN indicator (green), L/A OUT indicator (green), PWR indicator (green), RUN indicator (green), ERROR indicator (red), and SS (Sensor Status) indicator (green/red)
Vibration resistance (destruction)	10 to 60 Hz with a 0.7-mm double amplitude, 50 m/s² at 60 to 150 Hz, for 1.5 hours each in X, Y, and Z directions
Shock resistance (destruction)	150 m/s² for 3 times each in X, Y, and Z directions
Ambient temperature range	Operating: 0 to 55°C; *3 Storage: -30 to 70°C (with no icing or condensation)
Ambient humidity range	Operating and storage: 25% to 85% (with no condensation)
*Maximum connectable Sensors 3**	30 *4
Maximum connectable Distributed Sensor Units	8
Insulation resistance	20 MΩ min. (at 500 VDC)
Dielectric strength	500 VAC at 50/60 Hz for 1 min
Mounting method	35-mm DIN track - mounting
Weight (packed state/Unit only)	Approx. 185 g/approx. 95 g
Materials	Polycarbonate
Accessories	Power supply connector, communications connector for E3NW-DS connection, DIN Track End Plates (2 pieces), and instruction manual

*1. The E3NX-CA0 is supported for firmware version 1.06 or higher (Sensor Communications Units manufactured in
   June 2016 or later).
*2. The E9NC-TA0 is supported for firmware version 1.03 or higher (Sensor Communications Units manufactured in
   July 2014 or later).
*3. Temperature Limitations Based on Number of Connected Amplifier Units:
   Groups of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C, Groups of 11 to 16 Amplifier
   Units: 0 to 45°C, Groups of 17 to 30 Amplifier Units: 0 to 40°C
*4. You can connect up to 30 Sensors total to the Sensor Communications Unit and Distributed Sensor Units.

Communications Specifications

Item	Specification
Communications protocol	Dedicated protocol for EtherCAT
Modulation	Baseband method
Baud rate	100 Mbps
Physical layer	100BASE-TX (IEEE 802.3u)
Topology	Daisy chain
Communications media	STP category 5 or higher
Communications distance	Distance between nodes: 100 m max.
Noise immunity	Conforms to IEC 61000-4-4, 1 kV or higher
Node address setting method	Set with decimal rotary switches or software *1
Node address range	000 to 192 *2

*1. The software setting is used when the node address setting switches are set to 0.
*2. The range depends on the EtherCAT master that is used. Refer to the E3NW-ECT EtherCAT Digital Sensor
Communications Unit Operation Manual (Cat. No. E429) for details.

CompoNet

Model	E3NW-CRT
Connectable Sensor Amplifier Units	N-Smart Smart Fiber Amplifier Unit: E3NX-FA0 Smart Laser Amplifier Unit: E3NC-LA0 Smart Laser Amplifier Unit (CMOS type): E3NC-SA0
Power supply voltage	14 to 26.4 VDC
Power and current consumption	At 24 VDC 1.7 W max. (Not including the power supplied to Sensors.), 70 mA max. (Not including the current supplied to Sensors.)
Indicators	MS (Machine Status) indicator (green/red), NS (Network Status) indicator (green/red), and SS (Sensor Status) indicator (green/red)
Vibration resistance (destruction)	10 to 60 Hz with a 0.7-mm double amplitude, 50 m/s² at 60 to 150 Hz, for 1.5 hours each in X, Y, and Z directions
Shock resistance (destruction)	150 m/s² for 3 times each in X, Y, and Z directions
Ambient temperature range	Operating: 0 to 55°C; *1 Storage: -30 to 70°C (with no icing or condensation)
Ambient humidity range	Operating and storage: 25% to 85% (with no condensation)
*Maximum connectable Sensors 1**	16 *2
Maximum connectable Distributed Sensor Units	8
Insulation resistance	20 MΩ min. (at 500 VDC)
Dielectric strength	500 VAC at 50/60 Hz for 1 min
Mounting method	35-mm DIN track - mounting
Weight (packed state/Unit only)	Approx. 165 g/approx. 70 g
Materials	Polycarbonate
Accessories	Communications connector for E3NW-DS connection, DIN Track End Plates (2 pieces), and instruction manual

*1. Temperature Limitations Based on Number of Connected Amplifier Units:
Groups of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C, Groups of 11 to 16 Amplifier
Units: 0 to 45°C
*2. You can connect up to 16 Sensors total to the Sensor Communications Unit and Distributed Sensor Units.

Communications Specifications

Item	Specifications
Communications method	Dedicated protocol for CompoNet
Types of communications	Remote I/O communications (program-free, constant sharing of data) and message communications (explicit message communications as required)
Baud rate	4 Mbps, 3 Mbps, 1.5 Mbps, 93.75 kbps
Modulation	Baseband method
Coding	Manchester code
Error control	Manchester encoding rules and CRC
Communications media	The following media can be used. Round Cable I Round Cable II Flat Cable I (DCA4-4F10 Standard Flat Cable) Flat Cable II (DCA5-4F10 Sheathed Flat Cable) Note: Round Cable I, Round Cable II, Flat Cable I, and Flat Cable II cables are all treated as different types of cables. When two or more types of cables are used in a single network, a Repeater Unit must be used to separate any two different types of cables between the trunk line and a sub-trunk line.
Communications distance and wiring	Refer to 1-2-1 Cable Types, Maximum Distances, and Number of Slave Units in the CompoNet Master Units Operation Manual (Cat. No. W456).
Signal lines	Two lines: BDH (communications data high) and BDL (communications data low)
Power lines	Two lines: BS+ and BS- (power for communications and internal Slave Unit circuits) Power is supplied from the Master Unit or Repeater Unit.
Connection forms	Round Cable II, Flat Cable I, or Flat Cable II at a baud rate of 93.75 kbps: No restrictions Other cables or baud rates: Trunk line and branch lines
Connection forms	Connections for Slave Units and Repeater Units: T-branch or multidrop connections
Noise immunity	Conforms to IEC 61000-4-4, 1 kV or higher
Address setting method	Decimal rotary address switch
Address range	0 to 62

CC-Link

Model	E3NW-CCL
Connectable Sensor Amplifier Units	N-Smart Smart Fiber Amplifier Unit: E3NX-FA0 Smart Laser Amplifier Unit: E3NC-LA0 Smart Laser Amplifier Unit (CMOS type): E3NC-SA0 Contact-Type Smart Amplifier Unit: E9NC-TA0 *1
Power supply voltage	24 VDC (20.4 to 26.4 V)
Power and current consumption	2.4 W max. (Not including the power supplied to Sensors.), 100 mA max. (Not including the current supplied to Sensors.)
Indicators	RUN indicator (green), ERROR indicator (red), and SS (Sensor Status) indicator (green/red)
Vibration resistance (destruction)	10 to 60 Hz with a 0.7-mm double amplitude, 50 m/s² at 60 to 150 Hz, for 1.5 hours each in X, Y, and Z directions
Shock resistance (destruction)	150 m/s² for 3 times each in X, Y, and Z directions
Ambient temperature range	Operating: 0 to 55°C; *2 Storage: -30 to 70°C (with no icing or condensation)
Ambient humidity range	Operating and storage: 25% to 85% (with no condensation)
*Maximum connectable Sensors 2**	16 *3
Maximum connectable Distributed Sensor Units	8
Insulation resistance	20 MΩ min. (at 500 VDC)
Dielectric strength	500 VAC at 50/60 Hz for 1 min
Mounting method	35-mm DIN track - mounting
Weight (packed state/Unit only)	Approx. 180 g/approx. 80 g
Materials	Polycarbonate
Accessories	Power Supply Connector, E3NW-DS Communications Connector, Network Connectors (2), DIN Track End Plates (2), and Instruction Manual

*1. The E9NC-TA0 is supported for firmware version 1.03 or higher (Sensor Communications Units manufactured in
July 2014 or later).
*2. Temperature Limitations Based on Number of Connected Amplifier Units:
Groups of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C, Groups of 11 to 16 Amplifier
Units: 0 to 45°C
*3. You can connect up to 16 Sensors total to the Sensor Communications Unit and Distributed Sensor Units.

Communications Specifications

Item	Specifications
Communications protocol	Dedicated protocol for CC-Link
Communications method	Broadcast polling
Baud rate	10 Mbps/5 Mbps/2.5 Mbps/625 kbps/156 kbps
Physical layer	Bus (based on EIA RS485)
Topology	Daisy chain (T-branching can be used.)
Communications media	CC-Link Cables
Communications distance	Cable length between nodes: 20 cm min. Maximum total cable length Baud rate of 156 kbps: 1,200 m Baud rate of 625 kbps: 900 m Baud rate of 2.5 Mbps: 400 m Baud rate of 5 Mbps: 160 m Baud rate of 10 Mbps: 100 m
Noise immunity	Conforms to IEC 61000-4-4, 1 kV or higher
Address setting method	Decimal rotary address switch
Address range	64 max. *
Synchronization mode	Cyclic transmissions (synchronization)

* The range depends on the CC-Link master that is used. Refer to 5-3-2 Node Setting Switches in the E3NW-CCL CC-
Link Digital Sensor Communications Unit Operation Manual (Cat. No. E431) for details.

Distributed Sensor Unit

Model	E3NW-DS
Connectable Sensor Amplifier Units	N-Smart Smart Fiber Amplifier Unit: E3NX-FA0 Color Fiber Amplifier Unit: E3NX-CA0 Smart Laser Amplifier Unit: E3NC-LA0 Smart Laser Amplifier Unit (CMOS type): E3NC-SA0 Contact-Type Smart Amplifier Unit: E9NC-TA0
Power supply voltage	24 VDC (20.4 to 26.4 V)
Power and current consumption	2 W max. (Not including the power supplied to Sensors.), 80 mA max. (Not including the current supplied to Sensors.)
Indicators	RUN indicator (green) and SS (Sensor Status) indicator (green/red)
Vibration resistance (destruction)	10 to 60 Hz with a 0.7-mm double amplitude, 50 m/s² at 60 to 150 Hz, for 1.5 hours each in X, Y, and Z directions
Shock resistance (destruction)	150 m/s² for 3 times each in X, Y, and Z directions
Ambient temperature range	Operating: 0 to 55°C; * Storage: -30 to 70°C (with no icing or condensation)
Ambient humidity range	Operating and storage: 25% to 85% (with no condensation)
Maximum connectable Sensors *	10
Insulation resistance	20 MΩ min. (at 500 VDC)
Dielectric strength	500 VAC at 50/60 Hz for 1 min
Mounting method	35-mm DIN track - mounting
Weight (packed state/Unit only)	Approx. 160 g/approx. 40 g
Materials	Polycarbonate
Accessories	Power supply/communications connector, DIN Track End Plates (2 pieces), ferrite cores (2 pieces), and instruction manual

* Temperature Limitations Based on Number of Connected Amplifier Units:
Groups of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C

Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.

Sensor Communications Unit

E3NW-ECT

E3NW-CRT

E3NW-CCL

Distributed Sensor Unit

E3NW-DS

TITLE	DOCUMENT TYPE	SIZE
E3NW	Data Sheet	1029 KB
E3NW	Catalog	3002 KB
E3NW-CCL CC-Link Digital Sensor Communications Unit	Manual	12244 KB
E3NW-CRT CompoNet™ Digital Sensor Communications Unit	Manual	5326 KB
E3NW-ECT EtherCAT® Digital Sensor Communication Unit Operation	Manual	10453 KB
E3NW-ECT Digital Sensor Communication Unit NJ-series EtherCAT® Connection Guide	Technical Guide	2040 KB
E3NW-ECT Digital Sensor Communication Unit CJ Series EtherCAT® Connection Guide	Technical Guide	2077 KB
E3NC-LA0 Smart Laser Amplifier(ENG/JPN/CHI)	Instruction Manual	4158 KB
E3NC-SA0 Smart Laser (CMOS) Amplifier(ENG/JPN/CHI)	Instruction Manual	3890 KB
E3NW-DS Distributed Sensor Unit(Safety Precautions) (ENG/JPN/CHI)	Instruction Manual	1384 KB
E3NW-ECT EtherCAT Slave, Sensor Communication Unit(Safety Precautions) (ENG/JPN/CHI)	Instruction Manual	1488 KB
E3NX-FA0 Series Smart Fiber Amplifier(ENG/JPN/CHI)	Instruction Manual	3916 KB
E9NC-TA0 Contact-Type Smart Amplifier (Detection Type)(ENG/JPN/CHI)	Instruction Manual	7931 KB

Introduction

Radically Reduce Manufacturing Costs

Even if you implement a Sensor Network, the cost of introduction is greatly reduced.

Greatly Reduce Introduction Cost in Comparison to Previous Sensor Networks

Commissioning

Radically Reduce System Commissioning Time

Easy Batch Setting from a Touch Panel

Line Changeovers Are Also Easy with a Setup Backup Function

Operation

Radically Increase Machine Productivity

Monitoring for Predictive Maintenance

Reduced Downtime When Troubles Occur

Sensor Communications Unit

EtherCAT

Communications Specifications

CompoNet

Communications Specifications

CC-Link

Communications Specifications

Distributed Sensor Unit

Sensor Communications Unit

E3NW-ECT

E3NW-CRT

E3NW-CCL

Distributed Sensor Unit

E3NW-DS

Group Sites

Our Partner Sites

Subscribe Our Newsletter