The UHF RFID system with a wide communication range can identify the objects in various sizes on a line or the carts which take different routs.
last update: September 28, 2021
The UHF RFID system with a wide communication range can identify the objects in various sizes on a line or the carts which take different routs.
Even when two or more RF tags exist in the communication range, the reader/writer can read the target tag just in front of it. It reads RF tags in the order in which they are conveyed while ignoring RF tags on pallets around the line.
In addition to V780 RF Tags, the RF tags that conform to ISO/IEC 18000-63 (ISO/IEC 18000-6 Type C) can
be used.
Contact your Omron representative for details.
One reader/writer is set as a master, and others are set as slaves.
When the host device sends commands to the master reader/writer, the reader/writers work like one
reader/writer that has a wide communication range.
When simultaneously inspecting all stacked pallets passing through a portal, install the reader/writers on both the left and right sides of the portal to read an RF tag placed on either the left or right side of each pallet.
It takes time to locate a defective vehicle outside the assembly line or a finished vehicle ready for
shipment by using the on-board paper.
Place an RF tag on the dashboard of each vehicle and install reader/writers on the vehicle waiting space
to read the tags, which reduces the time to locate vehicles.
Use the V780-HMD68-ETN-[][]-S Slave Reader/Writer as a slave to inexpensively create a system with the
Multi-Reader/Writer function that expands the communication range.
* See Catalog for details.
*1. PATENT PENDING/PATENTED means that the patent was applied for or the patent was granted. (As of
August 2019)
*2. Version 3 or later provides this function.
The transmission power required for communications between the reader/writer and RF tags are measured
and automatically set to appropriate values. The set power will be large enough to communicate with RF
tags and minimize interference with other reader/writers.
This function is useful when multiple reader/writers are installed in one factory. The transmission
power can be easily set via the web browser.
This function visualizes reception levels, helping adjust installation positions of reader/writers and
RF tags and check communication ranges.
When RF tags on two or more objects are read for adjustment, connect your PC with the reader/writer to
check a time series graph of the reception levels via the web browser.
In addition to the web browser, the flashing speed of the LED indicators on the reader/writer provides a visual indication of the reception level. This makes it easier to install and adjust a reader/writer or RF tag at a production site.
By connecting a PC, you can set parameters and monitor communication status, noise levels, and communication log via the web browser. This facilitates maintenance and troubleshooting.
The latest 8,000 communication diagnostic results are listed in a table. When communications are unstable, the probable causes and workarounds are displayed to make troubleshooting easier. Also, a graph shows RSSI levels and noise levels to aid identify the causes of unstable communications. The diagnostic results can be output to CSV files.
Noise levels in the operating environment are displayed to allow you to check radio interference. You can identify noise sources and take measures to stabilize operation.
You can immediately check the communication status with the indicators of the reader/writer.
The indicators using high-brightness LED can be easily seen even from a distance.
The wide communication range and focus mode enable bodyworks to be reliably detected from several meters away.
The passing pallets can be detected correctly.
The LED indicators show in real time whether the pallet is detected.
Reception Level Monitor that shows reception levels over time helps installation. No special knowledge required.
High-brightness LED indicators that provide clear status indication can be seen from a distance.
The causes are visualized from 8,000 logged results. Channel monitor shows noise levels in the web browser to help identify the causes.
RFID systems as well as mobile phones and TVs must comply with national radio regulations.
The V780 Series currently complies with radio regulations in many countries and will comply with them in
other countries. For the list of countries where the V780 is available, please contact your Omron
representative for details.
last update: September 28, 2021
last update: September 28, 2021
Item | V780-HMD68-ETN-[][] | V780-HMD68-EIP-[][] | V780-HMD68-ETN-[][]-S |
---|---|---|---|
Dimensions | 250 × 250 × 70 mm (D × H × W, excluding protruding parts and cables) | ||
Supply voltage | 24 VDC (-15% to +10%) Class2 | ||
Power consumption | 10 W max. | ||
Ambient operating temperature | -10 to 55°C (with no icing) | ||
Ambient operating humidity | 25% to 85% (with no condensation) | ||
Ambient storage temperature | -25 to 70°C (with no icing) | ||
Ambient storage humidity | 25% to 85% (with no condensation) | ||
Insulation resistance | 20 MΩ min. (at 500 VDC) between cable terminals and case | ||
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 min between cable terminals and case | ||
Vibration resistance | No abnormality after application of 10 to 500
Hz, double amplitude: 1.5 mm,
acceleration: 100 m/s2, 10 sweeps in each of 3 axis directions (up/down, left/right, and forward/backward) for 11 minutes each |
||
Shock resistance | No abnormality after application of 500
m/s2, 3 times each in 6 directions
(Total: 18 times) |
||
Degree of protection | IP54 (IEC 60529:2001) | ||
Materials | Plastic case: PBT
Metal case: Die-cast aluminum (ADC12) |
||
Weight | Approx. 3 kg | ||
Mounting method | Four M6 bolts | ||
Host communications interface | Ethernet 10BASE-T/100BASE-TX | ||
Host communications protocol | Modbus/TCP base | EtherNet/IP | Multi-Reader/Writer Function only *1 |
Multi-Reader/Writer function | Master/Slave | Master/Slave | Slave |
Accessories | Instruction Sheet (1), IP address label (1),
Startup Guide (1), Ferrite core (2) *2,
and EU DECLARATION OF CONFORMITY (1) *3 |
||
Regulations | See Regulations on below for the regulations. |
*1. Communicates via the master reader/writer (V780-HMD68-E[][]-[][]) Although the PLC or other host
device cannot control the slaves, the Web Server function (browser interface) can be used.
*2. A ferrite core is packaged with Model V780-HMD68-ETN-EU/-IN.
*3. A EU DECLARATION OF CONFORMITY is packaged with Model V780-HMD68-ETN-EU.
Model | Regulations |
---|---|
V780-HMD68-ETN-JP
V780-HMD68-EIP-JP V780-HMD68-ETN-JP-S |
Premises Radio Station (920-MHz-band Moving Object Differentiation
Wireless Facilities),
ARIB STD-T106 |
V780-HMD68-ETN-KR
V780-HMD68-EIP-KR V780-HMD68-ETN-KR-S |
|
V780-HMD68-ETN-CN
V780-HMD68-EIP-CN V780-HMD68-ETN-CN-S |
Ministry of Information Industry No. 205 (2007) |
V780-HMD68-ETN-TW
V780-HMD68-EIP-TW V780-HMD68-ETN-TW-S |
NCC LP0002 4.8 RFID |
V780-HMD68-ETN-IN
V780-HMD68-EIP-IN V780-HMD68-ETN-IN-S |
the G.S.R.36 (E) |
V780-HMD68-ETN-MY
V780-HMD68-EIP-MY V780-HMD68-ETN-MY-S |
MCMC MTSFB TC T007:2014 |
V780-HMD68-ETN-SG
V780-HMD68-EIP-SG V780-HMD68-ETN-SG-S |
Singapore: IMDA TS SRD2
Thailand: NTC TS 1010-2550 (RFID 920-925 MHz) |
V780-HMD68-ETN-EU
V780-HMD68-EIP-EU V780-HMD68-ETN-EU-S |
2014/53EU (RE Directive) |
V780-HMD68-ETN-RU
V780-HMD68-EIP-RU V780-HMD68-ETN-RU-S |
к решению ГКРЧ от 07.05.2007
№ 07-20-03-001 |
V780-HMD68-ETN-US
V780-HMD68-EIP-US V780-HMD68-ETN-RU-S |
FCC 15.247 (United states)
ISED RSS-247 (Canada) |
V780-HMD68-ETN-MX
V780-HMD68-EIP-MX V780-HMD68-ETN-MX-S |
IFT-008
NYCE NOM-208 |
Item | V780-HMD68-ETN-JP/V780-HMD68-EIP-JP/V780-HMD68-ETN-JP-S |
---|---|
Applicable countries | Japan |
Maximum Radiated Power | 4 W e.i.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 20 kbps (Standard Mode) * |
Used frequencies
(Described at the center frequency of each channel) |
3 channels (916.8/918.0/919.2 MHz)
License station |
Channel interval | 200 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-KR/V780-HMD68-EIP-KR/V780-HMD68-ETN-KR-S |
---|---|
Applicable countries | Korea |
Maximum Radiated Power | 4 W e.i.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 6 channels (917.3/917.9/918.5/919.1/919.7/920.3 MHz)
FHSS |
Channel interval | 200 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-CN/V780-HMD68-EIP-CN/V780-HMD68-ETN-CN-S |
---|---|
Applicable countries | China |
Maximum Radiated power | 2 W e.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 20 kbps (Standard Mode) * |
Used frequencies | 16 channels (920.625 to 924.375 MHz)
FHSS |
Channel interval | 250 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-TW/V780-HMD68-EIP-TW/V780-HMD68-ETN-TW-S |
---|---|
Applicable countries | Taiwan |
Maximum Radiated power | 4 W e.i.r.p (indoor use only) |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 10 channels (922.75 to 927.25 MHz)
FHSS |
Channel interval | 500 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-IN/V780-HMD68-EIP-IN/V780-HMD68-ETN-IN-S |
---|---|
Applicable countries | India |
Maximum Radiated Power | 2 W e.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 3 channels (865.7/866.3/866.9 MHz)
FHSS |
Channel interval | 200 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-MY/V780-HMD68-EIP-MY/V780-HMD68-ETN-MY-S |
---|---|
Applicable countries | Malaysia |
Maximum Radiated power | 2 W e.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 8 channels (919.25 to 922.75 MHz)
FHSS |
Channel interval | 500 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-SG/V780-HMD68-EIP-SG/V780-HMD68-ETN-SG-S |
---|---|
Applicable countries | Singapore and Thailand |
Maximum Radiated Power | 2 W e.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 8 channels (920.75 to 924.25 MHz)
FHSS |
Channel interval | 500 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-EU/V780-HMD68-EIP-EU/V780-HMD68-ETN-EU-S |
---|---|
Applicable countries | Under RE direct |
Maximum Radiated Power | 2 W e.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 4 channels (865.7/866.3/866.9/867.5 MHz)
FHSS |
Channel interval | 200 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-RU/V780-HMD68-EIP-RU/V780-HMD68-ETN-RU-S |
---|---|
Applicable countries | Russia |
Maximum Radiated Power | 2 W e.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 3 channels (866.3/866.9/867.5 MHz)
FHSS |
Channel interval | 200 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | V780-HMD68-ETN-US/V780-HMD68-EIP-US/V780-HMD68-ETN-US-S |
---|---|
Applicable countries | United States and Canada |
Maximum Radiated Power | 4 W e.i.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 50 channels (902.75 to 927.25 MHz)
FHSS |
Channel interval | 500 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
* The default setting is for Automatic Mode. The Reader/Writer will automatically change to High-speed
Mode or Standard
Mode depending on the interference waves.
Item | V780-HMD68-ETN-MX/V780-HMD68-EIP-MX/V780-HMD68-ETN-MX-S |
---|---|
Applicable countries | Mexico |
Maximum Radiated Power | 4 W e.i.r.p |
Output power | 15 to 27 dBm (Switchable in 1-dB increments.) |
RSSI detection range | Signal level: -35 to -61 dBm
Noise level: -35 to -70 dBm (at end of antenna cable) |
Transmission speed from Reader/
Writer to RF Tag |
40 kbps (fixed) |
Transmission speed from RF Tag to
Reader/Writer |
• 80 kbps (High-speed Mode) *
• 31.25 kbps (Standard Mode) * |
Used frequencies | 50 channels (902.75 to 927.25 MHz)
FHSS |
Channel interval | 500 kHz |
Communications method with RF Tags | Miller-modulated subcarrier |
Tag communications protocol | ISO/IEC 18000-63: 2013 (EPCglobal Class-1 Generation-2) |
Polarization characteristic | RHCP |
Multiaccess communications | Up to 64 RF Tags can be read. |
Item | Condition |
---|---|
Supply voltage | 24 VDC -15% to +10% |
Output current | 500 mA min. |
Safety standard | SELV (Safety Extra Low Voltage) |
Model | V780-A-JIME-Z3BLI-10 (made by Toppan Forms Co., Ltd.) |
---|---|
Dimensions | 150 × 14 × 6 mm (W × H × D) |
IC chip, memory | Monza X 8K
UII (EPC): 128 bits User memory: 8,192 bits |
Write life / Data retention | 10,000 writes / 10 years |
100,000 writes / 1 year | |
Operating temperature | -20 to 65°C |
Operating humidity | 5% to 95% |
Storage temperature | -30 to 70°C |
Storage humidity | 5% to 95% |
Material | Polycarbonate plastic |
Weight | Tag: Approx. 15 g |
Degree of protection | IP68 (IEC 60529: 2001) |
Model | V780-A-TA-133 (made by Toppan Forms Co., Ltd.) |
---|---|
Dimensions | 180 × 50 × 30 mm (W × H × D) |
Operating temperature | -20 to 65°C |
Operating humidity | 5% to 95% |
Storage temperature | -30 to 70°C |
Storage humidity | 5% to 95% |
Material | Polycarbonate plastic |
Weight | Approx. 128 g |
last update: September 28, 2021
last update: September 28, 2021
(Unit: mm)
Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.
last update: September 28, 2021
TITLE | DOCUMENT TYPE | SIZE |
V780 Series Catalog | Catalog | 1426 KB |
---|---|---|
V780 Series Data Sheet | Data Sheet | 4829 KB |
V780 Series ETN Startup Guide | Instruction Sheet | 986 KB |
V780 Series EIP Startup Guide | Instruction Sheet | 811 KB |
V780 Series ETN (For Slave Reader/Writer Model) Startup Guide | Instruction Sheet | 2398 KB |