The new models carry on the simple operation and low cost of the series.
A wide variety of applications can be handled by using program settings with up to 256 segments.
last update: December 19, 2013
The new models carry on the simple operation and low cost of the series.
A wide variety of applications can be handled by using program settings with up to 256 segments.
Thermocouple or Pt: ±0.1% PV,
Analog input: 0.1% FS
High-resolution for Measurements, Fluctuation Detection, and Logging of Temperature and Humidity in Environmental Testing Equipment
Sampling Rate Sufficient to Handle Rapid Increases in Temperature
Stable Control of Objects Requiring High-speed Response by Handling Rapid Increases in Temperature, Such As for Ceramic Heaters
Five-digit PV/SV Display to 0.01°C for High Performance
Display to 0.01°C for Pt, K, J, or T.
Enables high-precision temperature control.
You can program up to 8 programs × 32 segments.
The CX-Thermo Support Software (Sold Separately) Enables Easy Setting and Control of Programs.
Easy Parameter Setting on a Computer Using the CX-Thermo (Sold Separately)
Using the trend monitor enables easy adjustment and maintenance.
Customize the menu display to match the worksite. Display can be turned OFF for parameters that are not necessary to better match the worksite.
This helps prevent incorrect operation for both the operator and the Controller.
Perform communications with a computer by using the infrared communications port on the front panel (except for the E5CN-H and E5CN-HT). The ability to use CX-Thermo from the front panel after the Controller has been mounted to a control panel reduces maintenance time.
Easily perform logic operations without a PLC.
Effectively use limited I/O by combining I/O bit status and alarm status through AND and OR logic operations or by inverting event input logic.
last update: December 19, 2013
Power supply voltage |
No D in model number: 100 to 240 VAC, 50/60 Hz D in model number: 24 VAC, 50/60 Hz; 24 VDC |
|
---|---|---|
Operating voltage range | 85% to 110% of rated supply voltage | |
Power consumption |
100 to 240 VAC: 12 VA 24 VAC/VDC: 8.5 VA (24 VAC)/5.5 W (24 VDC) |
|
Sensor input |
Any of the following can be selected. Thermocouple: K, J, T, E, L, U, N, R, S, B, W, or PL II Platinum resistance thermometer: Pt100 or JPt100 Current input: 4 to 20 mA or 0 to 20 mA Voltage input: 1 to 5 V, 0 to 5 V, or 0 to 10 V |
|
Input impedance |
Current input: 150 Ω max., Voltage input: 1 MΩ min. (Use a 1:1 connection when connecting the ES2-HB.) |
|
Control method | ON/OFF control or 2-PID control (with auto-tuning) | |
Control output |
Relay output | Output Unit (Install the Output Unit (sold separately).) |
Voltage output (for driving SSR) |
||
Current output | ||
Linear voltage output | ||
Relay output for position-proportional control |
Relay output: Open and close: SPST-NO, 250 VAC, 1 A (including in-rush current), electrical life: 100,000 operations min. Potentiometer input: Must be between 100 Ω and 2.5 kΩ for maximum open position. |
|
Auxiliary output |
Number of outputs | 2 or 3 max. |
Output specifications |
Relay output: SPST-NO, 250 VAC, 3 A (resistive load), electrical life: 100,000 operations, minimum applicable load: 5 V, 10 mA |
|
Event input |
Number of outputs | 2 or 4 (with an E53-AKB) |
External contact input specifications |
Contact input: ON: 1 kΩ max., OFF: 100 kΩ min. | |
Non-contact input: ON: Residual voltage: 1.5 V max., OFF: Leakage current: 0.1 mA max. |
||
Current flow: Approx. 7 mA per contact | ||
Logic operations |
Number of operations | 8 max. |
Operations |
Logic operation: Any of the following four patterns can be selected. The input status may be inverted. (A and B) or (C and D), (A or C) and (B or D), A or B or C or D, A and B and C and D (A, B, C, and D are four inputs.) Delay: ON delay or OFF delay for the results of the logic operation given above. Setting time: 0 to 9999 s or 0 to 9999 min Output inversion: Possible |
|
Output | One work bit per operation | |
Work bit assignment |
Any of The following can be assigned to up to eight work bits (logic operation results): operation commands (assigned to event inputs)* , auxiliary outputs, or control outputs. * Application is possible with models that do not have event inputs by using an internal assignment. |
|
Transfer outputs |
Number of outputs | 1 max. (Depends on model. Models with transfer output (F in model number) |
Output specifications |
Current output: 4 to 20 mA DC, Load: 600 Ω max., Resolution at 4 to 20 mA: Approx. 10,000 |
|
RSP input |
Number of inputs | 1 |
Signal type | Current input: 4 to 20 mA (input impedance: 150 Ω ± 10%) | |
Analog input scaling |
Scaling of signal to engineering units (EU) - 19,999 to 30,000 (display: 30,000 max.) |
|
Accuracy | ( ± 0.2% of FS) ± 1 digit max. | |
Input sampling period | 60 ms | |
Setting method | Set digitally using keys on the front panel or by using the RSP input. | |
Indication method |
11-segment digital display and individual indicators (7-segments displays also possible) Character height: E5AN-HT: PV: 15.8 mm, SV: 9.5 mm, MV: 6.8 mm; E5EN-HT: PV: 11.8 mm, SV: 8.1 mm, MV: 5.8 mm Three displays: PV/SV/Program number/Segment number, PV/SV/MV, or PV/ SV/Remaining segment time. Number of digits: 5 for PV and SV, 4 for MV |
|
Other functions |
Manual output, heating/cooling control, loop burnout alarm, other alarm functions, heater burnout detection (including SSR failure and heater overcurrent detection), 40% AT, 100% AT, MV limiter, input digital filter, temperature input shift, run/reset, protection functions, control output ON/OFF counter, extraction of square root, MV change rate limit, PV/SV status display, automatic cooling coefficient adjustment, program control functions, etc. |
|
Ambient operating temperature |
-10 to 55 °C (with no condensation or icing), for 3-year warranty: -10 to 50 °C |
|
Ambient operating humidity | 25% to 85% | |
Storage temperature | -25 to 65 °C (with no condensation or icing) |
Shaded settings are the default settings.
The applicable standards for the input types are as follows:
K, J, T, E, N, R, S, B: JIS C 1602-1995, IEC 584-1
L: Fe-CuNi, DIN 43710-1985
U: Cu-CuNi, DIN 43710-1985
W: W5Re/W26Re, ASTM E988-1990
JPt100: JIS C 1604-1989, JIS C 1606-1989
Pt100: JIS C 1604-1997, IEC 751
PL II: According to Platinel II electromotive force charts from BASF (previously Engelhard)
Set value |
Alarm type | Alarm output operation | Description of function | |
---|---|---|---|---|
When alarm value X is positive |
When alarm value X is negative |
|||
0 | Alarm function OFF | Output OFF | No alarm | |
1 |
Upper- and lower- limit *1 |
|
*2 |
Set the deviation in the set point by setting the alarm upper limit (H) and alarm lower limit (L). |
2 | Upper-limit |
|
|
Set the upward deviation in the set point by setting the alarm value (X). |
3 | Lower-limit |
|
|
Set the downward deviation in the set point by setting the alarm value (X). |
4 |
Upper- and lower- limit range *1 |
|
*3 |
Set the deviation in the set point by setting the alarm upper limit (H) and alarm lower limit (L). |
5 |
Upper- and lower- limit with standby sequence *1 |
*5 |
*4 |
A standby sequence is added to the upper- and lower- limit alarm (1). *7 |
6 |
Upper-limit with standby sequence |
|
|
A standby sequence is added to the upper-limit alarm (2). *7 |
7 |
Lower-limit with standby sequence |
|
|
A standby sequence is added to the lower-limit alarm (3). *7 |
8 |
Absolute-value upper-limit |
|
|
The alarm will turn ON if the process value is larger than the alarm value (X) regardless of the set point. |
9 |
Absolute-value lower-limit |
|
|
The alarm will turn ON if the process value is smaller than the alarm value (X) regardless of the set point. |
10 |
Absolute-value upper-limit with standby sequence |
|
|
A standby sequence is added to the absolute-value upper-limit alarm (8). *7 |
11 |
Absolute-value lower-limit with standby sequence |
|
|
A standby sequence is added to the absolute-value lower-limit alarm (9). *7 |
12 |
LBA (alarm 1 type only) |
--- | *7 | |
13 |
PV change rate alarm |
--- | *7 | |
14 |
RSP absolute value upper limit *6 |
|
|
The alarm turns ON when the remote SP (RSP) is larger than the alarm value (X). This alarm functions in both Local SP and Remote SP Modes. |
15 |
RSP absolute value lower limit *6 |
|
|
The alarm turns ON when the remote SP (RSP) is smaller than the alarm value (X). This alarm functions in both Local SP and Remote SP Modes. |
Indication accuracy |
Thermocouple: (± 0.1% of indicated value or ± 1 °C, whichever is greater) ± 1 digit max. *1 Platinum resistance thermometer: (± 0.1% of indicated value or ± 0.5 °C, whichever is greater) ± 1 digit max. Analog input: ± 0.1% FS ± 1 digit max. CT input: ± 5% FS ± 1 digit max. Potentiometer input: ±5% FS ±1 digit max. |
|
---|---|---|
Transfer output accuracy | ± 0.3% FS max. | |
Influence of temperature *2 |
Thermocouple input (R, S, B, W, PL II): (± 1% of PV or ± 10 °C, whichever is greater) ±1 digit max. Other thermocouple input: (± 1% of PV or ± 4 °C, whichever is greater) ± 1 digit max. *3 Platinum resistance thermometer: (± 1% of PV or ± 2 °C, whichever is greater) ± 1 digit max. Analog input: (± 1%FS) ± 1 digit max. |
|
Influence of voltage *2 | ||
Influence of EMS. (at EN 61326-1) |
||
Input sampling period | 60 ms | |
Hysteresis |
Temperature input: 0.1 to 3240.0 °C or °F (in units of 0.1 °C or °F) Analog input: 0.01% to 99.99% FS (in units of 0.01% FS) |
|
Proportional band (P) |
Temperature input: 0.1 to 3240.0 °C or °F (in units of 0.1 °C or °F) Analog input: 0.1% to 999.9% FS (in units of 0.1% FS) |
|
Integral time (I) | 0.0 to 3240.0 s (in units of 0.1 s) | |
Derivative time (D) | 0.0 to 3240.0 s (in units of 0.1 s) | |
Control period | 0.5, 1 to 99 s (in units of 1 s) | |
Manual reset value | 0.0 to 100.0% (in units of 0.1%) | |
Alarm setting range | -19999 to 32400 (decimal point position depends on input type) | |
Affect of signal source resistance |
Thermocouple: 0.1°C/Ω max. (100 Ω max.) Platinum resistance thermometer: 0.1°C/Ω max. (10 Ω max.) |
|
Insulation resistance | 20 MΩ min. (at 500 VDC) | |
Dielectric strength | 2,300 VAC, 50 or 60 Hz for 1 min (between terminals with different charge) | |
Vibration resistance |
Malfunction | 10 to 55 Hz, 20 m/s2 for 10 min each in X, Y, and Z directions |
Destruction | 10 to 55 Hz, 0.75-mm single amplitude for 2 hrs each in X, Y, and Z directions | |
Shock resistance |
Malfunction | 100 m/s2, 3 times each in X, Y, and Z directions |
Destruction | 300 m/s2, 3 times each in X, Y, and Z directions | |
Weight | E5AN-HT | Controller: Approx. 310 g, Mounting Bracket: Approx. 100 g |
E5EN-HT | Controller: Approx. 260 g, Mounting Bracket: Approx. 100 g | |
Degree of protection | Front panel: IP66, Rear case: IP20, Terminals: IP00 | |
Memory protection | Non-volatile memory (number of writes: 1,000,000 times) | |
Setup Tool | CX-Thermo version 4.0 or higher | |
Setup Tool port |
Provided on the bottom of the E5AN-HT and E5EN-HT. An E58-CIFQ1 USB-Serial Conversion Cable is required to connect the computer to the E5AN-HT and E5EN-HT. Provided on the front of the E5AN-HT and E5EN-HT. An E58-CIFIR USB-infrared Conversion Cabl is required to connect the computer to the E5AN-HT or E5EN-HT. *4 |
|
Standards |
Approved standards |
UL 61010-1, CSA C22.2 No. 1010-1 |
Conformed standards |
EN 61010-1 (IEC 61010-1): Pollution level 2, overcurrent category II | |
EMC |
EMI: EN 61326-1 *5 Radiated Interference Electromagnetic Field Strength: EN 55011 Group 1, class A Noise Terminal Voltage: EN 55011 Group 1, class A EMS: EN 61326-1 *5 ESD Immunity: EN 61000-4-2 Electromagnetic Field Immunity: EN 61000-4-3 Burst Noise Immunity: EN 61000-4-4 Conducted Disturbance Immunity: EN 61000-4-6 Surge Immunity: EN 61000-4-5 Power Frequency Magnetic Field Immunity: EN 61000-4-8 Voltage Dip/Interrupting Immunity: EN 61000-4-11 |
Number of programs (patterns) | 8 | |
---|---|---|
Number of segments (steps) | 32 | |
Segment setting method | Time setting (Segment set with set point and time.) | |
Gradient setting (Segment type with set point, gradient, and time.) | ||
Segment times | 0 h 0 min to 99 h 59 min | |
0 min 0 s to 99 min 59 s | ||
Alarm setting | Set separately for each program. | |
Reset operation | Select either stopping control or fixed SP operation. | |
Startup operation | Select continuing, resetting, manual operation, or run mode. | |
PID sets | Number of sets | 8 |
Setting method |
Set separately for each program (automatic PID group selection also supported). |
|
Alarm SP function | Select from ramp SP and target SP. | |
Program status control | Segment operation | Advance, hold |
Program operation | Program repetitions and program links | |
Wait operation | Wait method | Waiting at segment ends |
Wait width setting | Same wait width setting for all programs | |
Time signals | Number of outputs | 2 |
Number of ON/OFF Operations |
1 each per output | |
Setting method | Set separately for each program. | |
Program status output | Program end output (pulse width can be set), run output, stage output | |
Program startup operation | PV start | Select from segment 1 set point, slope-priority PV start |
Standby | 0 h 0 min to 99 h 59 min | |
0 day 0 h to 99 day 23h | ||
Operation end operation | Select from resetting, continuing control at final set point, and fixed SP control. | |
Program SP shift | Same program SP shift for all programs |
Applicable OS | Windows XP/Vista/7/8 |
---|---|
Applicable software | CX-Thermo version 4 or higher |
Applicable models |
E5AN/E5EN/E5CN/E5CN-U/E5AN-H/E5EN-H/E5CN-H/E5AN-HT/E5EN-HT/ E5CN-HT |
USB interface standard | Conforms to USB Specification 1.1. |
DTE speed | 38400 bps |
Connector specifications |
Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) |
Power supply | Bus power (Supplied from USB host controller.) |
Power supply voltage | 5 VDC |
Current consumption | 70 mA |
Ambient operating temperature | 0 to 55°C (with no condensation or icing) |
Ambient operating humidity | 10% to 80% |
Storage temperature | - 20 to 60°C (with no condensation or icing) |
Storage humidity | 10% to 80% |
Altitude | 2,000 m max. |
Weight | Approx. 100 g |
Transmission line connection method |
RS-485, RS-422: Multipoint RS-232C: Point-to-point |
---|---|
Communications |
RS-485 (two-wire, half duplex) RS-422 (four-wire, half duplex) or RS-232C |
Synchronization method | Start-stop synchronization |
Protocol | CompoWay/F or Modbus |
Baud rate | 1200, 2400, 4800, 9600, 19200, 38400, or 57600 bps |
Transmission code | ASCII (CompoWay/F) |
RTU (Modbus) | |
Data bit length * | 7 or 8 bits |
Stop bit length * | 1 or 2 bits |
Error detection |
Vertical parity (none, even, odd) Block check character (BCC) with CompoWay/F or CRC-16 Modbus |
Flow control | None |
Interface | RS-485, RS-422, or RS-232C |
Retry function | None |
Communications buffer | 217 bytes |
Communications response wait time |
0 to 99 ms Default: 20 ms |
Dielectric strength | 1,000 VAC for 1 min |
---|---|
Vibration resistance | 50 Hz, 98 m/s2 |
Weight | E54-CT1: Approx. 11.5 g, E54-CT3: Approx. 50 g |
Accessories (E54-CT3 only) |
Armatures (2) Plugs (2) |
Applicable OS | Windows XP/Vista/7/8 |
---|---|
Applicable software | CX-Thermo version 4.0 or higher |
Applicable models | E5AN-H/E5EN-H/E5AN-HT/E5EN-HT |
USB interface standard | Conforms to USB Specification 1.1. |
DTE speed | 38400 bps |
Connector specifications |
Computer: USB (type A plug) Temperature Controller: Infrared port (on front of Controller) |
Power supply | Bus power (Supplied from USB host controller.) |
Power supply voltage | 5 VDC |
Current consumption | 80 mA |
Ambient operating temperature | 0 to 55°C (with no condensation or icing) |
Ambient operating humidity | 10% to 80% |
Storage temperature | - 20 to 60°C (with no condensation or icing) |
Storage humidity | 10% to 80% |
Altitude | 2,000 m max. |
Weight | Approx. 130 g (with mounting adaptor) |
CT input (for heater current detection) |
Models with detection for single-phase heaters: One input Models with detection for single-phase or three-phase heaters: Two inputs |
---|---|
Maximum heater current | 50 A AC |
Input current indication accuracy | ±5% FS ±1 digit max. |
Heater burnout alarm setting range *1 |
0.1 to 49.9 A (in units of 0.1 A) Minimum detection ON time: 100 ms |
SSR failure alarm setting range *2 |
0.1 to 49.9 A (in units of 0.1 A) Minimum detection OFF time: 100 ms |
Heater overcurrent alarm setting range *3 |
0.1 to 49.9 A (in units of 0.1 A) Minimum detection ON time: 100 ms |
E58-CIFQ1
E53-COV16 (Six Covers provided.)
One set is packaged with the product.
Order Mounting Adapters separately if yours are lost or damaged.
Order the Waterproof Packing separately if it becomes lost or damaged.
The Waterproof Packing can be used to achieve an IP66 degree of protection.
(Deterioration, shrinking, or hardening of the waterproof packing may occur depending on the operating environment. Therefore, periodic replacement is recommended to ensure the level of waterproofing specified in IP66. The time for periodic replacement depends on the operating environment. Be sure to confirm this point at your site.
Consider one year a rough standard. OMRON shall not be liable for the level of water resistance if the customer does not perform periodic replacement.)
The Waterproof Packing does not need to be attached if a waterproof structure is not required.
Maximum continuous heater current: 50 A (50/60 Hz)
Number of windings: 400±2
Winding resistance: 18±2 Ω
Maximum continuous heater current: 120 A (50/60 Hz)
(Maximum continuous heater current for an OMRON Temperature Controller is 50 A.)
Number of windings: 400±2
Winding resistance: 8±0.8 Ω
TITLE | DOCUMENT TYPE | SIZE |
E5AN-HT, E5EN-HT | Catalog | 2184 KB |
---|---|---|
Safety Precautions for E5N, E5N-H, E5N-HT | Catalog | 1325 KB |
Operation for E5N, E5N-H, E5N-HT | Catalog | 1526 KB |
E5CN-HT, E5AN-HT, E5EN-HT (Programmable Type) Digital Controllers User's |
Manual | 9143 KB |
E5CN-HT, E5AN-HT, E5EN-HT (Programmable Type) Digital Controllers Communications |
Manual | 1221 KB |
E5AN-HT Digital Controller |
Manual | 984 KB |
E58-CIFIR USB-Infrared Conversion Cable |
Manual | 9003 KB |
E58-CIFQ1 USB-Serial Conversion Cable |
Manual | 6857 KB |
EST2-2C-MV4 Measuring & Control Component Configurator (Install Guide) |
Manual | 298 KB |