Omron, XW2R (PLCs)

• Wiring patterns that are specifically designed for PLCs reduce the work required to check signal layout.

• Terminal block signal labels give the PLC addresses.

• Models available with Phillips screw, slotted screw, push-in, or e-CON connections.

• Models available with and without power supply terminals.

• Mounting to DIN Track is possible.

Models for Connection to OMRON PLCs

with power supply terminals

Push-in spring

Rated current		16 Points: 1 A/signal, 4 A/common 32 Points: 1 A/signal, 8 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 ferrulemin (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 24 to 14 (ferrules) AWG 28 to 14 (stranded or solid) (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG 28-16: 8 to 10 mm AWG 14: 9 to 10 mm

e-CON Type

Rated current		Power supply terminal block: 4 A/16 poles or 8 A/32 poles
Rated current		Connectors/e-CON Connectors: 1 A (However, rated current of e-CON Connector depends on the wires that are used.)
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 24 to 14 (ferrules) AWG 28 to 14 (stranded wires) AWG 28 to 16 (solid wires) * (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG 28-16: 8 to 10 mm AWG 14: 9 to 10 mm

* This is the applicable range for the power supply terminal block. For the applicable wire sizes for I/O Connectors (e-CON), refer to "Input Device Connectors: XN2 e-CON Connectors".

without power supply terminals

Phillips screw

Rated current		0.5 A/signal, 4 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 22 to 16 (round or forked crimp terminals) AWG 26 to 16 (stranded or solid wires)
	Stripped length	9 mm
	Tightening	0.5 Nm

Slotted screw (rise up)

Rated current		0.5 A/signal, 4 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 22 to 16 (ferrules) AWG 26 to 16 (stranded or solid wires)
	Stripped length	7 mm
	Tightening	0.5 to 0.6 Nm

Push-in spring

Rated current		0.5 A/signal, 4 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 24 to 14 (ferrules) AWG 28 to 14 (stranded or solid) (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG 28-16: 8 to 10 mm AWG 14: 9 to 10 mm

Models for Connection to Mitsubishi PLCs

with power supply terminals

XW2R-G32GD-M1-COM

Rated current		Power supply terminal block: 8 A Connectors: 1 A
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 24 to 14 (ferrules) AWG 28 to 14 (stranded wires) AWG 28 to 16 (solid wires) (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG 28-16: 8 to 10 mm, AWG 14: 9 to 10 mm

XW2R-N08GD-COM

Rated current		Power supply terminal block: 2A Connectors/e-CON Connectors: 1 A (However, rated current of e-CON Connector depends on the wires that are used.)
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes *	AWG 24 to 14 (ferrules), AWG 28 to 14 (stranded wires), AWG 28 to 16 (solid wires) (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG28-16: 8 to 10 mm, AWG14: 9 to 10 mm

* This is the applicable range for the power supply terminal block. For the applicable wire sizes for I/O Connectors (e-CON), refer to "Input Device Connectors: XN2 e-CON Connectors".

Push-in spring

Rated current		1 A/signal, 8 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 24 to 14 (ferrules) AWG 28 to 14 (stranded or solid) (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG 28-16: 8 to 10 mm AWG 14: 9 to 10 mm

without power supply terminals

Phillips screw

Rated current		0.5 A/signal, 2 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 22 to 16 (round or forked crimp terminals) AWG 26 to 16 (stranded or solid wires)
	Stripped length	9 mm
	Tightening	0.5 Nm

Slotted screw (rise up)

Rated current		0.5 A/signal, 2 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 22 to 16 (ferrules) AWG 26 to 16 (stranded or solid wires)
	Stripped length	7 mm
	Tightening	0.5 to 0.6 Nm

Push-in spring

Rated current		0.5 A/signal, 2 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 24 to 14 (ferrules) AWG 28 to 14 (stranded or solid) (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG 28-16: 8 to 10 mm AWG 14: 9 to 10 mm

Models for Keyence PLCs

with power supply terminals

Push-in spring

Rated current		1 A/signal, 8 A/common
Rated voltage		24 VDC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 24 to 14 (ferrules) AWG 28 to 14 (stranded or solid) (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG 28-16: 8 to 10 mm AWG 14: 9 to 10 mm

without power supply terminals

Phillips screw

Rated current		1A
Rated voltage		125 VAC/DC
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 22 to 16 (round or forked crimp terminals) AWG 26 to 16 (stranded or solid wires)
	Stripped length	9 mm
	Tightening	0.5 Nm

Push-in spring

Rated current		1A
Rated voltage		AC/DC 125 V
Insuration resistance		100 MΩ min. (at 500 VDC)
Dielectric strength		500 VAC for 1 min (leakage current: 1 mA max.)
Ambient operating temperature		0 to 55°C
Applicable wires	Applicable wire sizes	AWG 24 to 14 (ferrules), AWG 28 to 14 (stranded or solid wires) (Outer diameter of insulation must be 4 mm max)
Applicable wires	Stripped length	AWG 28-16: 8 to 10 mm, AWG 14: 9 to 10 mm

Input Device Connectors: XN2 e-CON Connectors

Rated current	3 A/pin (with AWG 20 wires), 2 A/pin (with AWG 22 wires), 1 A/pin (with AWG 24 wires), 0.5 A/pin (with AWG 26 or AWG 28 wires)
Rated voltage	32 VDC
Contact resistance	30 mΩ max. (at 20 mV, 100 mA max.)
Insuration resistance	10³ MΩ min. (at 500 VDC)
Dielectric strength	1,000 VAC for 60 sec (leakage current: 1 mA max.)
Insertion durability	50 times
Ambient operating temperature	-30 to 75°C *
Applicable wires	Stranded wire 0.08mm² (AWG28) to 0.5mm² (AWG20) (Outer diameter of insulation must be 1.5 mm max)

* The operating temperature range is restricted by the maximum operating temperature of the cable.

Models for Connection to OMRON PLCs

with power supply terminals

PLC Connecting Cables

XW2Z-[][][]B, XW2Z-[][][][]BF-L
Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

Wiring Diagram

XW2Z-[][][]K, XW2Z-[][][][]FF-L
Connectors: One 40-pin Connector to One 40-pin MIL Connector

Wiring Diagram

Push-in spring

Wiring Diagram

XW2R-P16GD-C1-COM

XW2R-P16GD-C3-COM

XW2R-P32GD-C1-COM

XW2R-P32GD-C2-COM

XW2R-P32GD-C3-COM

XW2R-P32GD-C4-COM

e-CON Type

Wiring Diagram

XW2R-N16GD-C1-COM

XW2R-N32GD-C1-COM

Please click image to enlarge (open in a new window).

XW2R-N32GD-C2-COM

Please click image to enlarge (open in a new window).

without power supply terminals

Phillips screw

Wiring Diagram

XW2R-J34GD-C1

XW2R-J34GD-C2

XW2R-J34GD-C3

XW2R-J34GD-C4

Slotted screw (rise up)

Wiring Diagram

XW2R-E34GD-C1

XW2R-E34GD-C2

XW2R-E34GD-C3

XW2R-E34GD-C4

Push-in spring

Wiring Diagram

XW2R-P34GD-C1

XW2R-P34GD-C2

XW2R-P34GD-C3

XW2R-P34GD-C4

Models for Connection to Mitsubishi PLCs

with power supply terminals

XW2Z-[][][]B, XW2Z-[][][][]BF-L
Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

Wiring Diagram

XW2Z-[][][]AA
One 14-pin MIL Connector to One 14-pin MIL Connector

Wiring Diagram

XW2R-G32GD-M1-COM

Wiring Diagram

XW2R-N08GD-COM

The e-CON address assignments are for combining the XW2R-G32GD-M1-COM with four XW2R-N08GD-COM.

Wiring Diagram

Push-in spring

Wiring Diagram

XW2R-P32GD-M1-COM

XW2R-P32GD-M2-COM

without power supply terminals

XW2Z-[][][]B, XW2Z-[][][][]BF-L
Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

Wiring Diagram

Phillips screw

Wiring Diagram

XW2R-J34GD-M1

XW2R-J34GD-M2

Slotted screw (rise up)

Wiring Diagram

XW2R-E34GD-M1

XW2R-E34GD-M2

Push-in spring

Wiring Diagram

XW2R-P34GD-M1

XW2R-P34GD-M2

Models for Keyence PLCs

with power supply terminals

XW2Z-[][][]EE, XW2Z-[][][]EE-L
Connectors: One 34-pin MIL Connector to One 34-pin MIL Connector

Wiring Diagram

Push-in spring

Wiring Diagram

XW2R-P32GD-K1-COM

without power supply terminals

XW2Z-[][][]EE, XW2Z-[][][][]EE-L
Connectors: One 34-pin MIL Connector to One 34-pin MIL Connector

Wiring Diagram

XW2Z-[][][]K, XW2Z-[][][][]FF-L
Connectors: One 40-pin MIL Connector to One 40-pin MIL Connector

Wiring Diagram

Phillips screw

Wiring Diagram

XW2R-J34GD-K1

XW2R-J40GD-K2

Push-in spring

Wiring Diagram

XW2R-P34GD-K1

XW2R-P40GD-K2

TITLE	DOCUMENT TYPE	SIZE
XW2R (PLCs)	Catalog	10607 KB
XW2R Series	Catalog	21665 KB
XW2[] Series Table of Connector-Terminal Block Conversion Units and connectable device combinations	Catalog	978 KB

Models for Connection to OMRON PLCs

with power supply terminals

Push-in spring

e-CON Type

without power supply terminals

Phillips screw

Slotted screw (rise up)

Push-in spring

Models for Connection to Mitsubishi PLCs

with power supply terminals

XW2R-G32GD-M1-COM

XW2R-N08GD-COM

Push-in spring

without power supply terminals

Phillips screw

Slotted screw (rise up)

Push-in spring

Models for Keyence PLCs

with power supply terminals

Push-in spring

without power supply terminals

Phillips screw

Push-in spring

Input Device Connectors: XN2 e-CON Connectors

Models for Connection to OMRON PLCs

with power supply terminals

PLC Connecting Cables

XW2Z-[][][]B, XW2Z-[][][][]BF-L Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

Wiring Diagram

XW2Z-[][][]K, XW2Z-[][][][]FF-L Connectors: One 40-pin Connector to One 40-pin MIL Connector

Wiring Diagram

Push-in spring

Wiring Diagram

XW2R-P16GD-C1-COM

XW2R-P16GD-C3-COM

XW2R-P32GD-C1-COM

XW2R-P32GD-C2-COM

XW2R-P32GD-C3-COM

XW2R-P32GD-C4-COM

e-CON Type

Wiring Diagram

XW2R-N16GD-C1-COM

XW2R-N32GD-C1-COM

XW2R-N32GD-C2-COM

without power supply terminals

Phillips screw

Wiring Diagram

XW2R-J34GD-C1

XW2R-J34GD-C2

XW2R-J34GD-C3

XW2R-J34GD-C4

Slotted screw (rise up)

Wiring Diagram

XW2R-E34GD-C1

XW2R-E34GD-C2

XW2R-E34GD-C3

XW2R-E34GD-C4

Push-in spring

Wiring Diagram

XW2R-P34GD-C1

XW2R-P34GD-C2

XW2R-P34GD-C3

XW2R-P34GD-C4

Models for Connection to Mitsubishi PLCs

with power supply terminals

XW2Z-[][][]B, XW2Z-[][][][]BF-L Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

Wiring Diagram

XW2Z-[][][]AA One 14-pin MIL Connector to One 14-pin MIL Connector

Wiring Diagram

XW2R-G32GD-M1-COM

Wiring Diagram

XW2R-N08GD-COM

Wiring Diagram

Push-in spring

Wiring Diagram

XW2R-P32GD-M1-COM

XW2R-P32GD-M2-COM

without power supply terminals

XW2Z-[][][]B, XW2Z-[][][][]BF-L Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

Wiring Diagram

XW2Z-[][][]B, XW2Z-[][][][]BF-L
Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

XW2Z-[][][]K, XW2Z-[][][][]FF-L
Connectors: One 40-pin Connector to One 40-pin MIL Connector

XW2Z-[][][]B, XW2Z-[][][][]BF-L
Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

XW2Z-[][][]AA
One 14-pin MIL Connector to One 14-pin MIL Connector

XW2Z-[][][]B, XW2Z-[][][][]BF-L
Connectors: One 40-pin Connector Made by Fujitsu Component, Ltd. to One 40-pin MIL Connector

XW2Z-[][][]EE, XW2Z-[][][]EE-L
Connectors: One 34-pin MIL Connector to One 34-pin MIL Connector

XW2Z-[][][]EE, XW2Z-[][][][]EE-L
Connectors: One 34-pin MIL Connector to One 34-pin MIL Connector

XW2Z-[][][]K, XW2Z-[][][][]FF-L
Connectors: One 40-pin MIL Connector to One 40-pin MIL Connector