• High-brightness ODR lighting beyond the limitations of LEDs.
• Stable inspection even for high-speed applications.
• Bright even through a polarizing filter.
• Easy wiring, mounting, and adjustment.
• High-brightness ODR lighting beyond the limitations of LEDs.
• Stable inspection even for high-speed applications.
• Bright even through a polarizing filter.
• Easy wiring, mounting, and adjustment.
The cable can extend from either direction, allowing for horizontal or vertical wiring layouts on the mounting surface.
The light is structured for mounting with nuts to an arm on the back or side surfaces.
Minute changes in the position can be achieved by sliding the light.
Specialized mounting brackets enable mounting at a flexible angle.
• High brightness in a small package.
•Wide range of working distance.
• No separate power supply is required because the power is supplied from the Camera.
• Light is emitted when a trigger signal is received from the Camera.
• Simple connection between the Camera and the Lighting with a single cable
With a compact design small enough to fit in the palm of your hand, the Controller can be built into the control panel or in the gap between production lines.
By using the longest lighting cable in the industry (25 m), the Controller can be installed along with the image processing monitor in a variety of locations. It is possible to adjust the lighting while looking at the screen.
This enables light emission synchronized with the camera using essentially any trigger, such as a photoelectric sensor.
The Controller can be connected to an image processing device to control lighting without any programming on a PLC.
[ Control Output ]
• PNP/NPN models
• Power source: 24 V
[ Lighting Emission Controls ]
• Lighting triggers can be used individually for each channel.
• Lighting delay and lighting time can be controlled.
Digital adjustment of light emission makes it easy to reproduce the lighting environment after line switchovers.
last update: December 19, 2016
Model | Wide Area
Model |
High-
brightness Model |
Wide Area
Model |
High-
brightness Model |
Wide Area
Model |
High-
brightness Model |
---|---|---|---|---|---|---|
FL-
BR5020W |
FL-
BR5020W-H |
FL-
BR9120W |
FL-
BR9120W-H |
FL-
BR13120W |
FL-
BR13120W-H |
|
Light source | White LEDs | |||||
Vibration resistance | 10 to 150 Hz (Double amplitude: 0.7 mm), 80 min each in X, Y, and Z directions | |||||
Shock resistance | 150 m/s2 3 times each in 6 directions | |||||
Ambient temperature | Operating: 0 to 40°C, Storage: -15 to 60°C (with no icing or condensation) | |||||
Ambient humidity | Operating/storage: 35% to 85% (with no condensation) | |||||
Ambient atmosphere | No corrosive gases. | |||||
Degree of protection | IEC60259 IP20 | |||||
Weight | Approx. 40 g | Approx. 70 g | Approx. 100 g | |||
Materials | Case and Lens:PC, Cable:Heat resistant, Connector:Thermoplastic resin with glass | |||||
LED safety | Risk Group 2 (IEC 62471) | |||||
Accessories | Instruction sheet |
The color of white LEDs can vary due to intrinsic characteristics.
Confirm suitability for the application in advance.
Model | Wide Area
Model |
High-
brightness Model |
Wide Area
Model |
High-
brightness Model |
Wide Area
Model |
High-
brightness Model |
---|---|---|---|---|---|---|
FL-DR32W | FL-DR32W-H | FL-DR50W | FL-DR50W-H | FL-DR90W | FL-DR90W-H | |
Light source | White LEDs | |||||
Vibration resistance | 10 to 150 Hz (Double amplitude: 0.7 mm), 80 min each in X, Y, and Z directions | |||||
Shock resistance | 150 m/s2 3 times each in 6 directions | |||||
Ambient temperature | Operating: 0 to 40°C, Storage: -15 to 60°C (with no icing or condensation) | |||||
Ambient humidity | Operating/storage: 35% to 85% (with no condensation) | |||||
Ambient atmosphere | No corrosive gases. | |||||
Degree of protection | IEC60259 IP20 | |||||
Weight | Approx. 25 g | Approx. 30 g | Approx. 70 g | Approx. 80 g | ||
Materials | Case and Lens:PC, Cable:Heat resistant, Connector:Thermoplastic resin with glass | |||||
LED safety | Risk Group 2 (IEC 62471) | |||||
Accessories | Instruction sheet |
The color of white LEDs can vary due to intrinsic characteristics.
Confirm suitability for the application in advance.
Product type | Lighting Controller | |
---|---|---|
Model | FL-TCC1 | |
Input voltage | Supplied from applicable camera. | |
Applicable camera | FH-S/SC/S02/SC02/S04/SC04, FZ-S/SC/S2M/SC2M/S5M2/SC5M2/SH/SHC/SF/
SFC/SP/SPC, FQ-MS series and others. |
|
Applicable controller | FH series, FZ5 series, FZ4 series and others. | |
Power consumption | 10 W, 0.9 A max. (including the lighting section) | |
Number of output channels | 1 | |
Applicable lighting | FL-[] series | |
Luminance
control method |
Functions | PWM frequency: 100 kHz, Light adjustment: 255 levels (set with the Controller) |
Trigger lighting | Lighting ON synchronized with trigger input timing from the Controller.
(Auto setting in accordance with the shutter speed.) |
|
Trigger lighting
delay time |
Ton: 30 μs max. (Trigger ready μs)
Toff: 10 μs max. |
|
External interface | Dedicated communication connector | |
Ambient temperature | Operating: 0 to 50°C, Storage: -15 to 60°C (with no icing or condensation) | |
Ambient humidity | Operating/storage: 35% to 85% (with no condensation) | |
Vibration resistance | 10 to 55 Hz, (0.7 mm double amplitude) 80 min each in X, Y, and Z directions | |
Shock resistance | 150 m/s2 3 times each in 6 directions (up/down, left/right, forward/backward) | |
Materials | Case: SECC, Cable: PVC | |
Degree of protection | IP20 (IEC60529) | |
Weight | Approx. 110 g | |
Accessories | Instruction sheet, Insulation sheet, Mounting screw (M2 ✕ 6 mm) ✕ 4 | |
Applicable standards | EN61326-1 * |
* Electromagnetic environment: Industrial electromagnetic environment (EN/IEC 61326-1 Table 2) also, the following condition is applied to the immunity test of this product. There are case that Lighting brightness fluctuate Max 10%.
Product type | One-channel models | Two-channel models | |||
---|---|---|---|---|---|
I/O type | NPN | PNP | NPN | PNP | |
Model | FL-STC10 | FL-STC15 | FL-STC20 | FL-STC25 | |
Power supply voltage | 24 VDC±10% (including ripple) | ||||
Power consumption | 36 W, 1.5 A max. (including the lighting
section) |
72 W, 3 A max. (including the lighting
section) |
|||
Number of output channels | 1 | 2 | |||
Applicable light | FL-[] Series | ||||
Luminance
control method |
CONTINUOUS
mode |
While the Strobe Controller power source is ON, light is continuously emitted.
PWM frequency: 100 kHz, Light adjustment: 400 levels |
|||
EXTERNAL
TRIGGER mode |
Lighting in synchronization with an external trigger input.
Lighting duration: Continuous while the trigger is input, or 0.1 to 99.9 ms (set in 0.1-ms increments) PWM frequency: 100 kHz, Light adjustment: 400 levels |
||||
STOROBE
mode |
Lighting in synchronization with the external trigger input, but twice brighter than
EXTERNAL TRIGGER mode. Lighting pulse width: 0.01 to 5 ms (light adjustment: 500 levels equivalent) |
||||
Luminance
adjustment |
Key | Luminance control method and adjustment value: Slide switch and cross key setting | |||
I/O | Luminance adjustment value: 9-bit binary input control | ||||
External interface | Parallel I/O connector (D-sub 15-pin), Terminal block (external trigger input with 2
terminals, power source voltage input with 2 terminals) |
||||
Ambient temperature | Operating: 0 to 40°C, Storage: -15 to 60°C (with no icing or condensation) | ||||
Ambient humidity | Operating/storage: 35% to 85% (with no condensation) | ||||
Vibration resistance | 10 to 150 Hz (0.7 mm double amplitude), 80 min each in X, Y, and Z directions | ||||
Shock resistance | 150 m/s2 3 times each in 6 direction (up/down, left/right, forward/backward) | ||||
Materials | Case: PC | ||||
Degree of protection | IEC60529 IP20 | ||||
Weight | Approx. 100 g | ||||
Accessories | Instruction sheet,Terminal block connector | ||||
Applicable standards | EN61326-1 * |
* Electromagnetic environment: Industrial electromagnetic environment (EN/IEC 61326-1 Table 2) also, the following condition is applied to the immunity test of this product. There are case that Lighting brightness fluctuate Max 10%.
last update: December 19, 2016
Camera Mounting Spacer
FL-TCC1-XSP (sold separately)
Camera Mounting Attachment
FL-TCC1-XAT (sold separately)
TITLE | DOCUMENT TYPE | SIZE |
Vision Accessory | Catalog | 48346 KB |
---|---|---|
FL-BR-20DF FL series Lighting for Image Processing Diffusion Plate for Bar Lighting |
Manual | 6024 KB |
FL-BR-20W-H FL series Lighting for Image Processing Bar Lighting |
Manual | 755 KB |
FL-DR-DF FL series Lighting for Image Processing Diffusion Plate for Direct Ring Lighting |
Manual | 470 KB |
FL-DR-PL FL series Lighting for Image Processing Polarization Plate for Direct Ring Lighting |
Manual | 666 KB |
FL-DR-W-H FL series Lighting for Image Processing Direct Ring Lighting |
Manual | 804 KB |
FL-STC FL series Lighting for Image Processing Lighting Controller |
Manual | 534 KB |
FL-TCC1 FL series Lighting for Image Processing Lighting Controller |
Manual | 9938 KB |
FL-XBK1 FL series Lighting for Image Processing Bracket for Bar Lighting |
Manual | 4573 KB |
FL-XC-R FL series Lighting for Image Processing Extension Cable |
Manual | 5936 KB |
FL-XCP2 FL series Lighting for Image Processing Parallel I/O Cable |
Manual | 4752 KB |